Nissan Rogue (T33) 2021-Present Service Manual: P2135 Tp Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2135 Tp Sensor

DTC Description

DTC DETECTION LOGIC

NOTE:

If DTC P2135 is displayed with DTC P06B0, first perform the trouble diagnosis for DTC P06B0. Refer to DTC Description.

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2135 00

TP SENSOR-B1

(Throttle/Pedal position sensor/switch “A” / “B” voltage correlation) 		Diagnosis condition Engine running at idle
Signal (terminal) TP sensor 1 signal and TP sensor 2 signal
Threshold Rationally incorrect voltage is sent to ECM compared with the signals from TP sensor 1 and TP sensor 2
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connector (TP sensor 1 or 2 circuit is open or shorted.)

  • Electric throttle control actuator (TP sensor 1 or 2)

  • Sensor power supply 1 and 2 circuit

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 1 second.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK THROTTLE POSITION SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect electric throttle control actuator harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between electric throttle control actuator harness connector and ground.

    + −

    Voltage

    (Approx.)
    Electric throttle control actuator
    Connector Terminal
    F50 3 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between electric throttle control actuator harness connector and ground.

    + − Continuity
    Electric throttle control actuator ECM
    Connector Terminal Connector Terminal
    F50 3 F72 62 Existed

  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

    + − Continuity
    Electric throttle control actuator ECM
    Connector Terminal Connector Terminal
    F50 2 F72 45 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

    + − Continuity
    Electric throttle control actuator ECM
    Connector Terminal Connector Terminal
    F50 1 F72 57 Existed
    4 52

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair open circuit or short to ground or short to power in harness or connectors.

CHECK THROTTLE POSITION SENSOR

Check the throttle position sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace electric throttle control actuator. Refer to Removal and Installation.

    P212d Admission Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P212D 00 Throttle position sensor/switch (Throttle Position Sens...
    P2138 App Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2138 00 APP SENSOR (Throttle/Pedal position sensor/switch D / E...

    Other materials:

    Basic Inspection. Diagnosis and Repair Work Flow
    Work Flow (Heated Steering Wheel) DETAILED FLOWOBTAIN INFORMATION ABOUT SYMPTOM Interview the customer to obtain the malfunction information (conditions and environment when the malfunction occurred) as much as possible when the customer brings the Nissan Ariya vehicle in. >> GO TO ...

    Power Supply and Ground Circuit
    Combination Meter Diagnosis Procedure CHECK FUSES Check that the following fuses are not blown: Unit Location Fuse No. Capacity Combination meter Fuse block (J/B) 29 5A 6 5A Is the fuse blown? YES>> Replace the blown fuse after repairing the affected circ ...

    Removal and Installation. Wind Deflector
    Exploded View Refer to Exploded View. Removal and Installation REMOVALFully open the glass lid. Disengage wind deflector fixing points using a remover tool (A) from moonroof unit assembly. Disengage wind deflector fixing pawl using a remover tool (A), and then remove wind deflector. ...