Nissan Rogue (T33) 2021-Present Service Manual: P212d Admission Valve Position Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P212d Admission Valve Position Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P212D 00

Throttle position sensor/switch

(Throttle Position Sensor/Switch "G" Circuit High) 		Diagnosis condition IGN ON
Signal (terminal) ADM valve position signal
Threshold

  • An excessively high voltage from the ADM valve is sent to ECM

  • An excessively　high position output from the ADM valve is sent to ECM.
Diagnosis delay time 1 second

POSSIBLE CAUSE

  • Harness or connectors (ADM valve circuit is open or shorted.)

  • ADM valve

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 2 seconds.

  2. Start engine and let it idle for 5 seconds.

  3. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ADM VALVE CONNECTOR

Visually check for ADM valve connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the ADM valve connector.

CHECK ADM VALVE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect ADM valve harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between ADM valve harness connector and ground.

    + −

    Voltage

    (Approx.)
    ADM valve
    Connector Terminal
    F93 5 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK ADM VALVE POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ADM valve harness connector and ECM harness connector.

    + − Continuity
    ADM valve ECM
    Connector Terminal Connector Terminal
    F93 5 F71 84 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK ADM VALVE GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ADM valve harness connector and ECM harness connector.

    + − Continuity
    ADM valve ECM
    Connector Terminal Connector Terminal
    F93 4 F71 107 Existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK ADM VALVE SIGNAL CIRCUIT

  1. Check the continuity between ADM valve harness connector and ECM harness connector.

    + − Continuity
    ADM valve ECM
    Connector Terminal Connector Terminal
    F93 6 F72 51 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK ADM VALVE

Check the ADM valve. Refer to Component Inspection.

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace ADM valve. Refer to Removal and Installation.

    P212c Admission Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P212C 00 Throttle position sensor/switch (Throttle Position Sens...
    P2135 Tp Sensor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P2135 is displayed with DTC P06B0, first perform the trouble diagnosis for DTC P06B0. Refer to DTC Description. DTC CONSULT scree...

    Other materials:

    Fuel Injector and Fuel Tube
    Exploded View Fuel rail pressure sensor High pressure fuel rail insulator High pressure fuel rail O-ring (black) Support disc Fuel injector Decoupling element Valve seat Retaining ring spring Holding down appliance Stud bolt     ...

    B2601-42 Memory Failure for Firmware Over the Air
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition B2601-42 Memory failure for firmware over the air Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold Errors are detected in the memory for software auto ...

    P06e6 Internal Control Module
    DTC Description DESCRIPTIONECM supplies a voltage of 5 V to some of the sensors systematically divided into 3 groups, respectively. Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously in the sensors belonging to the same group as the s ...