Nissan Rogue (T33) 2021-Present Service Manual: P212c Admission Valve Position Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P212c Admission Valve Position Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P212C 00

Throttle position sensor/switch

(Throttle Position Sensor/Switch "G" Circuit Low) 		Diagnosis condition IGN ON
Signal (terminal) ADM valve position signal
Threshold

  • An excessively low voltage from the ADM valve is sent to ECM

  • An excessively　low position output from the ADM valve is sent to ECM.
Diagnosis delay time 1 second

POSSIBLE CAUSE

  • Harness or connectors (ADM valve circuit is open or shorted.)

  • ADM valve

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 2 seconds.

  2. Start engine and let it idle for 5 seconds.

  3. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ADM VALVE CONNECTOR

Visually check for ADM valve connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the ADM valve connector.

CHECK ADM VALVE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect ADM valve harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between ADM valve harness connector and ground.

    + −

    Voltage

    (Approx.)
    ADM valve
    Connector Terminal
    F93 5 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK ADM VALVE POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ADM valve harness connector and ECM harness connector.

    + − Continuity
    ADM valve ECM
    Connector Terminal Connector Terminal
    F93 5 F71 84 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK ADM VALVE GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ADM valve harness connector and ECM harness connector.

    + − Continuity
    ADM valve ECM
    Connector Terminal Connector Terminal
    F93 4 F71 107 Existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK ADM VALVE SIGNAL CIRCUIT

  1. Check the continuity between ADM valve harness connector and ECM harness connector.

    + − Continuity
    ADM valve ECM
    Connector Terminal Connector Terminal
    F93 6 F72 51 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK ADM VALVE

Check the ADM valve. Refer to Component Inspection.

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace ADM valve. Refer to Removal and Installation.

    P212b Admission Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P212B 00 Throttle position sensor/switch (Throttle Position Sens...
    P212d Admission Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P212D 00 Throttle position sensor/switch (Throttle Position Sens...

    Other materials:

    B24b4-02 A/c Control Comm
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24B4-02 A/C CONTROL COMM (Air conditioning control communication) Diagnosis condition Ignition switch ON Signal (Terminal) LIN (A/C switch assembly) signal ...

    Removal and Installation. Steering Gear and Linkage
    Exploded View 1. Outer socket 2. Boot clamp (small diameter) 3. Boot 4. Boot clamp (large diameter) 5. Hole cover seal A. Outer socket lock nut. B. Inner socket lock nut. — — — — CAUTION: Never apply the grease to the surface be ...

    P0420 Three Way Catalyst Function
    DTC Description The ECM monitors the switching frequency ratio of air fuel ratio (A/F) sensor 1 and heated oxygen sensor 2.A three way catalyst (manifold) with high oxygen storage capacity will indicate a low switching frequency of heated oxygen sensor 2. As oxygen storage capacity decreases, ...