Nissan Rogue (T33) 2021-Present Service Manual: P02cd Fuel Injector

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P02cd Fuel Injector

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P02CD 00

CYL1 INJECTOR OFFSET LEARNING

(Cylinder 1 Fuel Injector "A" Offset Learning At Max Limit) 		Diagnosis condition

  • Engine running

  • During injector offset learning
Signal —
Threshold

  • Injector valve opening delay time grater than threshold.

  • Injector valve closing delay time less than threshold.

  • Injector offset correction value grater than threshold.
Diagnosis delay time —

POSSIBLE CAUSE

  • ECM

  • Fuel injector (Cylinder 1)

  • Harness or connectors (Fuel injector circuit is open or shorted.)

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P02CD is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-1

With CONSULT

  1. Turn ignition switch ON.

  2. Select “COOLANT TEMP/S” in “DATA MONITOR” mode of “ENGNE” using CONSULT.

  3. Check the following condition;

    COOLANT TEMP/S : 5 – 40°C (41 – 104°F)

Is the condition satisfied?

YES>>

GO TO 4.

NO>>

  1. Satisfy the condition.

  2. Retry from step 2.

PERFORM DTC CONFIRMATION PROCEDURE-2

With CONSULT

  1. Start the engine.

  2. Select “COOLANT TEMP/S” in “DATA MONITOR” mode of “ENGNE” using CONSULT.

  3. Maintain the following condition for 20 seconds or more at idle.

    COOLANT TEMP/S : 60°C (140°F) or more

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO>>

GO TO 5.

PERFORM DTC CONFIRMATION PROCEDURE-3

With CONSULT

  1. Perform “Fuel injector offset learning” in “WORK SUPPORT” mode of “ENGINE” using CONSULT.

  2. Maintain the following condition for 10 seconds.

    Electrical load signal

    • A/C switch: ON

    • Electric load: ON (Lights, heater fan & rear window defogger)
    Engine speed 2,000 - 3,000 rpm

  3. Check DTC.

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P02CD is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK FUEL INJECTOR

  1. Check fuel injector. Refer to Component Function Check.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

  3. Check DTC.

Is the DTC P02CD displayed again?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE FUEL INJECTOR

  1. Replace fuel injector at cylinder 1. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

  3. Check DTC.

Is the DTC P02CD displayed again?

YES>>

GO TO 4.

NO>>

INSPECTION END

REPLACE ECM

Replace ECM. Refer to ECM : Removal & Installation.

>>

INSPECTION END

    P02cc Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02CC 00 CYL1 INJECTOR OFFSET LEARNING (Cylinder 1 Fuel Injector...
    P02ce Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02CE 00 CYL2 INJECTOR OFFSET LEARNING (Cylinder 2 Fuel Injector...

    Other materials:

    P02ee Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02EE 00 Cylinder 1 injector (Cylinder 1 Injector Circuit Range/Performance) Diagnosis condition Injector compensation control is operating Signal — ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...

    Main Line Between Lib 12v and M&a Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side). Harness connector B41 Harness con ...