Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Reclining Motor

Nissan Rogue (T33) 2021-Present Service Manual / Body Interior :: Automatic Drive Positioner / Dtc/circuit Diagnosis :: Reclining Motor

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Reclining motor” in “Active test” mode of “DRIVER SEAT”.

  3. Check reclining motor LH operation.

Test item Operation
Reclining motor Forward Seat reclining Forward
Backward Backward
Stop Stop

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK RECLINING MOTOR POWER SUPPLY VOLTAGE

CONSULT

  1. Ignition switch OFF.

  2. Disconnect reclining motor LH connector.

  3. Ignition switch ON.

  4. Select “Reclining motor” in “Active test” mode of “DRIVER SEAT”.

  5. Check voltage between reclining motor LH harness connector and ground.

    (+) (-) Condition

    Voltage

    (Approx.)
    Reclining motor LH
    Connector Terminal
    B217 1 Ground Reclining motor Forward Battery voltage
    Backward 0 V
    Stop 0 V
    3 Forward 0 V
    Backward Battery voltage
    Stop 0 V

Is the inspection result normal?

YES>>

Replace seat back frame. Refer to Disassembly and Assembly.

NO>>

GO TO 2.

CHECK RECLINING MOTOR POWER SUPPLY CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect driver seat control unit connector.

  3. Check continuity between reclining motor LH harness connector and driver seat control unit harness connector.

    Reclining motor LH Driver seat control unit Continuity
    Connector Terminal Connector Terminal
    B217 1 B214 47 Yes
    3 56

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK RECLINING MOTOR POWER SUPPLY CIRCUIT (SHORT TO GROUND)

Check continuity between reclining motor LH harness connector and ground.

Reclining motor LH (—) Continuity
Connector Terminal
B217 1 Ground No
3

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

    Dtc/circuit Diagnosis. U2118-87 Can Comm Err (intelligent Key)
    DTC Description CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high ...
    Dtc/circuit Diagnosis. Memory Indicator
    Component Function Check CHECK FUNCTION Push set switch. Check memory indicator operation. When driver seat position is already retained in memory : Illuminated for 5 seconds Wh...

    Other materials:

    Main Line Between Avm and Sonar Circuit
    Diagnosis Procedure CHECK HARNESS CONTINUITY (OPEN CIRCUIT) Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Disconnect the following harness connectors. Around view monitor control unit Sonar control unit ADAS control unit 2 ...

    P1574 Ascd Vehicle Speed Sensor
    DTC Description DESCRIPTIONThe ECM receives two vehicle speed sensor signals via CAN communication line. One is sent from VDC (Nissan Ariya vehicle dynamics control), and the other is from TCM (Transmission control module). The ECM uses these signals for ASCD control. Refer to System Descri ...

    Intelligent Key battery replacement
    WARNING Do not ingest the battery — Chemical Burn Hazard. This product contains a coin/button cell battery. If swallowed, it can cause severe internal burns within hours and may lead to death. Keep both new and used batteries away from children. If the battery compartment of your Nissan R ...