Nissan Rogue (T33) 2021-Present Service Manual: P0850 Pnp Switch

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0850 Pnp Switch

DTC Description

DESCRIPTION

Transmission range switch is turn ON when the selector lever is P or N.

ECM detects the position because the continuity of the line (the ON) exists.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0850 00

P-N POS SW/CIRCUIT

(Park/Neutral switch input circuit) 		Diagnosis condition —
Signal (terminal) Park/neutral position (PNP) signal
Threshold The signal of transmission range switch is not changed in the process of engine starting and driving
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

  • Transmission range switch

  • TCM

  • Electric shift control module

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0850 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

CHECK PNP SIGNAL FUNCTION

With CONSULT

  1. Ignition switch ON.

  2. Select “P/N POSI SW” in “DATA MONITOR” mode of “ENGINE” using CONSULT. Then check the “P/N POSI SW” signal as per the following conditions.

    Selector lever position Known-good signal
    N or P position ON
    Except above position OFF

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Refer to DTC Diagnosis Procedure.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Select “DATA MONITOR” mode of “ENGINE” using CONSULT.

  2. Start engine and warm it up to normal operating temperature.

  3. Maintain the following conditions for at least 60 consecutive seconds.

    CAUTION:

    Always drive Nissan Ariya vehicle at a safe speed.

    ENG SPEED 1,000 - 6,375 rpm
    COOLANT TEMP/S More than 65°C (149°F)
    B/FUEL SCHDL 3.25 - 31.8 msec
    VHCL SPEED SE More than 64 km/h (40 mph)
    Selector lever Suitable position

  4. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-2>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0850 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK DTC WITH TCM

Check DTC with TCM. Refer to DTC Index.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform trouble shooting relevant to DTC indicated.

CHECK DTC WITH ELECTRIC SHIFT CONTROL MODULE

Check DTC with electric shift control module. Refer to DTC Index.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Perform trouble shooting relevant to DTC indicated.

CHECK TRANSMISSION RANGE SWITCH

Check the transmission range switch. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace transmission range switch. Refer to Transmission Range Switch.

    P0719 Brake Pedal Switch B
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0719 Brake pedal switch B (Brake Switch "B" Circuit Low) Diagno...
    P0a1e Sub Starter & Generator
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0A1E 00 Starter/generator control module (Starter/generator con...

    Other materials:

    Système d'essuie-glace automatique avec détecteur de pluie du Nissan Rogue
    Le Nissan Rogue est doté d'une technologie de détection de précipitations intelligente. Ce système d'essuie-glace automatique, assisté par un capteur de pluie optique situé sur la partie supérieure du pare-brise (derrière le rétroviseur intérieur), est capable d'activer les balais sa ...

    Adas Control Unit. Basic Inspection
    Additional Service When Replacing Adas Control Unit 2 Without Propilot Assist 2.1 Work Procedure Always perform the additional service after replacing the ADAS control unit 2.ADAS CONTROL UNIT 2 CONFIGURATION Perform saving Nissan Ariya vehicle internal information according to "Replace ECU" i ...

    P0441 Evap Control System
    DTC Description DTC DETECTION LOGICIn this evaporative emission (EVAP) control system, purge flow occurs during non-closed throttle conditions. Purge volume is related to air intake volume. Under normal purge conditions (non-closed throttle), the EVAP canister purge volume control solenoid ...