Nissan Rogue (T33) 2021-Present Service Manual: P0719 Brake Pedal Switch B

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0719 Brake Pedal Switch B

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0719

Brake pedal switch B

(Brake Switch "B" Circuit Low) 		Diagnosis condition

  • When a deceleration G of -0.13 G or more occurs after the Nissan Ariya vehicle speed exceeds 30 km/h (19 MPH).

  • When the brake normal close switch (Brake pedal position switch) is pressed.
Signal (terminal) CAN communication signal
Threshold The stop lamp switch is released until 2 seconds have passed after the Nissan Ariya vehicle has stopped when the diagnosis condition is established. Malfunction is confirmed when the above condition is established 5 times.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (Stop lamp switch circuit is open.)

  • Stop lamp switch (BCM)

FAIL-SAFE

Not applicable

CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 2 seconds.

  2. Repeat the following step 5 times.

    1. Drive the Nissan Ariya vehicle and accelerate to 48 km/h (30 MPH).

    2. Decelerate from 48 km/h (30 MPH) to 0 km/h (0 MPH) within 7 seconds.

    3. Stop the Nissan Ariya vehicle for 2 seconds or more.

      CAUTION:

      Always drive vehicle at a safe speed.

      NOTE:

      This procedure may be conducted with the drive wheels lifted in the shop or by driving the Nissan Ariya vehicle. If a road test is expected to be easier, it is unnecessary to lift the vehicle.

  3. Check DTC.

Is DTC P0719 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM BCM DIAGNOSIS

Perform BCM diagnosis. Refer to DTC Index.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

REPLACE ECM

Replace ECM. Refer to ECM : Removal & Installation.

>>

INSPECTION END

    P06e6 Internal Control Module
    DTC Description DESCRIPTIONECM supplies a voltage of 5 V to some of the sensors systematically divided into 3 groups, respectively. Accordingly, when a short circuit develops in...
    P0850 Pnp Switch
    DTC Description DESCRIPTIONTransmission range switch is turn ON when the selector lever is P or N.ECM detects the position because the continuity of the line (the ON) exists.DTC...

    Other materials:

    Basic Inspection. System Setting
    Description The settings of the automatic driving positioner system can be changed, using information display in the combination meter and the set switch. Always check the settings before and after replacing driver seat control unit. For details, refer to Work Procedure.×: ApplicableSetting ...

    Informations de base
    Le système d’arrêt au ralenti du Nissan Rogue est conçu pour réduire la consommation de carburant, limiter les émissions de gaz d’échappement et diminuer les nuisances sonores inutiles lorsque le véhicule est immobilisé. Lorsque vous immobilisez le Nissan Rogue, le moteur s’arrête ...

    Calibrating Camera Image (intelligent Around View Monitor)
    Without Propilot Assist 2.1 Work Procedure Calibration must be performed after removing/replacing the cameras, removing parts (e.g. front grille, door mirror, and others) mounted on the cameras, or replacing the around view monitor control unit. The use of CONSULT is required to per ...