Nissan Rogue (T33) 2021-Present Service Manual: Tail Lamp Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Exterior Lighting System / Led Headlamp :: Dtc/circuit Diagnosis / Tail Lamp Circuit

Component Function Check

CHECK TAIL LAMP OPERATION

  1. Ignition switch ON.

  2. With operating the lighting switch, check that the tail lamp is turned ON.

    Lighting switch 1ST : Tail Lamp ON
    Lighting switch OFF or AUTO* : Tail lamp OFF

    *: Only when the illumination judgement by intelligent auto light system is OFF.

Is the inspection result normal?

YES>>

Tail lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK TAIL LAMP OUTPUT VOLTAGE

  1. Ignition switch ON.

  2. With operating the lighting switch, check voltage between IPDM E/R harness connector and ground.

    *: Only when the illumination judgement by intelligent auto light system is OFF.

    + - Condition

    Voltage

    (Approx.)
    IPDM E/R
    Connector Terminal
    RH E119 4 Ground Lighting switch 1ST Battey voltage
     
    LH
    OFF or AUTO* 0 V

    *: Only when the illumination judgement by intelligent auto light system is OFF.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK TAIL LAMP POWER SUPPLY CIRCUIT 1

  1. Turn lighting switch OFF or AUTO.

  2. Ignition switch OFF.

  3. Disconnect the following connectors:

    • IPDM E/R

    • Rear combination lamp LH (body side)

    • Rear combination lamp RH (body side)

    • Rear combination lamp LH (back door side)

    • Rear combination lamp RH (back door side)

    • License plate lamp LH

    • License plate lamp RH

  4. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R — Continuity
Connector Terminal
RH E119 4 Ground No
LH

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK TAIL LAMP POWER SUPPLY CIRCUIT 2

  1. Turn lighting switch OFF or AUTO.

  2. Ignition switch OFF.

  3. Disconnect IPDM E/R connector and rear combination lamp connector.

  4. Check continuity between IPDM E/R harness connector and each rear combination lamp harness connector.

    Rear combination lamp (body side)
    IPDM E/R Rear combination lamp (body side) Continuity
    Connector Terminal Connector Terminal
    RH E119 4 B102 2 Yes
    LH B90
    Rear combination lamp (back door side)
    IPDM E/R Rear combination lamp (back door side) Continuity
    Connector Terminal Connector Terminal
    RH E119 4 D519 6 Yes
    LH D518

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK TAIL LAMP GROUND CIRCUIT

Check continuity between each rear combination lamp harness connector and ground.

Rear combination lamp (body side)
Rear combination lamp (body side) — Continuity
Connector Terminal
RH B102 1 Ground Yes
LH B90
Rear combination lamp (back door side)
Rear combination lamp (back door side) — Continuity
Connector Terminal Terminal
RH D519 5 Ground Yes
LH D518

Is the inspection result normal?

YES-1>>

Body side: Check corresponding rear combination lamp (body side) sub harness, if there is a malfunction, repair or replace. If there is no malfunction, replace the corresponding rear combination lamp (body side). Refer to Removal and Installation.

YES-2>>

Back door side: Check corresponding rear combination lamp (back door side) sub harness, if there is a malfunction, repair or replace. If there is no malfunction, replace the corresponding rear combination lamp (back door side). Refer to Removal and Installation.

NO>>

Repair or replace harness.

    B2c96-49 Light Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B2C96-49 Light sensor (Light sensor) Diagnosis condition Whe...
    License Plate Lamp Circuit
    Component Function Check CHECK TAIL LAMP OPERATION Check that tail lamp is turned ON when lighting switch is turned 1ST. Is the inspection result normal? YES>> GO TO 2. NO...

    Other materials:

    P060a Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P060A 00 CONTROL MODULE (Internal control module monitoring processor performance) Diagnosis condition Engine running at idle Signal (terminal) — ...

    Assistance au freinage
    Assistance au freinage Lorsque la force exercée sur la pédale de frein dépasse un certain seuil, le système d’assistance au freinage du Nissan Rogue s’active automatiquement. Dans ce cas, la force de freinage appliquée devient supérieure à celle d’un système conventionnel, même ...

    Ivc Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side). TCU 8CH CAN gateway Is the ...