Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Memory Indicator

Component Function Check

CHECK FUNCTION

  1. Push set switch.

  2. Check memory indicator operation.

    When driver seat position is already retained in memory : Illuminated for 5 seconds
    When driver seat position is not retained in memory : Illuminated for 0.5 second

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK MEMORY INDICATOR OPERATION

Check memory indicator operation.

Which is the malfunctioning indicator?

All indicators are NG>>

GO TO 2.

An indicator is NG>>

GO TO 4.

CHECK FUSE

Check that the following fuse is not blown (open).

Signal name Fuse No. Capacity
Memory indicator power supply 26 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 3.

CHECK MEMORY INDICATOR POWER SUPPLY VOLTAGE

  1. Disconnect seat memory switch connector.

  2. Check voltage between seat memory switch harness connector and ground.

    (+) (-) Voltage (Approx.)
    Seat memory switch
    Connector Terminal
    D15 2 Ground Battery voltage

Is the inspection result normal?

YES>>

Replace seat memory switch. Refer to Removal and Installation.

NO>>

Repair the memory indicator power supply circuit.

CHECK MEMORY INDICATOR SIGNAL VOLTAGE

Check voltage between seat memory switch harness connector and ground.

(+) (-) Voltage (Approx.)
Seat memory switch
Connector Terminal
D15 3 Ground Battery voltage
4

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace seat memory switch. Refer to Removal and Installation.

CHECK MEMORY INDICATOR SIGNAL CIRCUIT (OPEN)

  1. Disconnect seat memory switch connector and driver seat control unit connector.

  2. Check continuity between seat memory switch harness connector and driver seat control unit harness connector.

    Seat memory switch Driver seat control unit Continuity
    Connector Terminal Connector Terminal
    D15 3 B213 38 Yes
    4 18

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair the harness or connector.

CHECK MEMORY INDICATOR SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between seat memory switch harness connector and ground.

Seat memory switch (—) Continuity
Connector Terminal
D15 3 Ground No
4

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

    Dtc/circuit Diagnosis. Reclining Motor
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Reclining motor” in “Active test” mode of “DRIVER SEAT”. Check reclining motor LH operati...
    Dtc/circuit Diagnosis. Reclining Sensor
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Reclining motor position” in “Data monitor” mode of “DRIVER SEAT”. Check reclining sensor...

    Other materials:

    Intelligent Key battery replacement
    WARNING Do not ingest the battery — Chemical Burn Hazard. This product contains a coin/button cell battery. If swallowed, it can cause severe internal burns within hours and may lead to death. Keep both new and used batteries away from children. If the battery compartment of your Nissan R ...

    Removal and Installation. Door Mirror
    Exploded View Door mirror cover (with side turn signal lamp) Door mirror finisher Side turn signal lamp (with side turn signal lamp) Door mirror base Door mirror actuator Glass mirror Blind cap Side camera (with side camera) Side camera bracket (with s ...

    Removal and Installation. Inside Key Antenna
    Japan Production Models Removal and Installation REMOVALRemove luggage rear plate. Refer to Removal and Installation. Remove inside key antenna fixing clips , and then remove inside key antenna . INSTALLATIONNote the following items, and then install in the reverse order of removal.CAUTION: N ...