Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Rear Wiper Stop Position Signal Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Wiper & Washer / Dtc/circuit Diagnosis :: Rear Wiper Stop Position Signal Circuit

Component Function Check

CHECK REAR WIPER STOP POSITION SIGNAL

CONSULT

  1. Select “Rear wiper auto stop switch” in “Data monitor” mode of “BCM”.

  2. Operate the rear wiper.

  3. Check that “Rear wiper auto stop switch” changes to “On” and “Off” linked with the wiper operation.

    Monitor item Condition Monitor status
    Rear wiper auto stop switch Rear wiper motor Rear wiper stop position On
    Any position other than rear wiper stop position Off

Is the inspection result normal?

YES>>

Rear wiper stop position signal circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK REAR WIPER MOTOR (AUTO STOP) OUTPUT VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect rear wiper motor connector.

  3. Ignition switch ON.

  4. Check voltage between rear wiper motor harness connector and ground.

    (+) (−)

    Voltage

    (Approx.)
    Rear wiper motor
    Connector Terminal
    D506 2 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3

NO>>

GO TO 2.

CHECK REAR WIPER MOTOR (AUTO STOP) CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and rear wiper motor harness connector.

    With type A meter
    BCM Rear wiper motor Continuity
    Connector Terminal Connector Terminal
    B123 90 D506 2 Yes
    With type B meter
    BCM Rear wiper motor Continuity
    Connector Terminal Connector Terminal
    B26 103 D506 2 Yes

  4. Check continuity between BCM harness connector and ground.

    With type A meter
    BCM (—) Continuity
    Connector Terminal
    B123 90 Ground No
    With type B meter
    BCM (—) Continuity
    Connector Terminal
    B26 103 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK REAR WIPER MOTOR GROUND OPEN CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between rear wiper motor harness connector and ground.

    Rear wiper motor (—) Continuity
    Connector Terminal
    D506 3 Ground Yes

Is the inspection result normal?

YES>>

Replace rear wiper motor. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. Rear Wiper Motor Circuit
    Component Function Check CHECK REAR WIPER OPERATION CONSULT Select “Rear wiper” in "Active test" mode of "BCM". With operating the test item, check rear wiper operation. On ...
    Dtc/circuit Diagnosis. Front Washer Circuit
    Component Function Check CHECK FRONT WASHER OPERATION When the front washer switch is turned to the ON position the front washer should operate. Is front washer operation normal...

    Other materials:

    Dtc/circuit Diagnosis. P161d-00 Immobilizer
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition P161D-00 IMMOBILIZER (Immobilizer) Diagnosis condition Ignition switch ON Signal (terminal) — Threshold When Intelligent Key unit detects an immob ...

    C10b1-01 Parking Brake Actuator (lh)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B1 01 Parking brake actuator (LH) [Parking brake actuator (left)] Diagnosis condition When parking brake is apply or release Signal (terminal) — ...

    Dtc/circuit Diagnosis. Thigh Support Motor
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Thigh support motor” in “Active test” mode of “DRIVER SEAT”. Check thigh support motor LH operation. Test item Operation Thigh support motor Up Thigh support Upward Down ...