Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Front Washer Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Wiper & Washer / Dtc/circuit Diagnosis :: Front Washer Circuit

Component Function Check

CHECK FRONT WASHER OPERATION

When the front washer switch is turned to the ON position the front washer should operate.

Is front washer operation normal?

YES>>

Washer switch circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to Symptom Table.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning part.

CHECK FRONT AND REAR WASHER PUMP FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    Location No. Capacity
    IPDM E/R 81 15A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit.

NO>>

GO TO 3.

CHECK FRONT WASHER PUMP RELAY OUTPUT VOLTAGE

  1. Disconnect front and rear washer pump relay connector.

  2. Ignition switch ON.

  3. Check voltage between front and rear washer pump relay harness connector and ground.

    (+) (−)

    Voltage

    (Approx.)
    Front and rear washer pump relay
    Connector Terminal
    E39 2 Ground Battery voltage
    3

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK FRONT WASHER PUMP RELAY CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between IPDM E/R harness connector and front and rear washer pump relay harness connector.

    IPDM E/R Front and rear washer pump relay Continuity
    Connector Terminal Connector Terminal
    E121 43 E39 2 Yes
    3

  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R (—) Continuity
    Connector Terminal
    E121 43 Ground No

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK FRONT WASHER PUMP RELAY CIRCUIT 2

  1. Ignition switch OFF.

  2. Connect front and rear washer pump relay connector.

  3. Ignition switch ON.

  4. Check voltage between front and rear washer pump relay harness connector and ground.

    (+) (−) Condition

    Voltage

    (Approx.)
    Front and rear washer pump relay
    Connector Terminal
    E39 4 Ground Front washer switch ON 0 V
    OFF Battery voltage

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 6.

CHECK FRONT WASHER PUMP RELAY CIRCUIT 3

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector and front and rear washer pump relay connector.

  3. Check continuity between IPDM E/R harness connector and front and rear washer pump relay harness connector.

    IPDM E/R Front and rear washer pump relay Continuity
    Connector Terminal Connector Terminal
    E119 5 E39 4 Yes

  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R (—) Continuity
    Connector Terminal
    E119 5 Ground No

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK FRONT WASHER PUMP RELAY

Check front washer pump relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Replace front washer pump relay.

CHECK FRONT AND REAR WASHER PUMP CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect front and rear washer pump connector and front and rear washer pump relay connector.

  3. Check continuity between front and rear washer pump harness connector and front and rear washer pump relay harness connector.

    Front and rear washer pump Front and rear washer pump relay Continuity
    Connector Terminal Connector Terminal
    E41 2 E39 1 Yes

  4. Check continuity between front and rear washer pump relay harness connector and ground.

    Front and rear washer pump relay (—) Continuity
    Connector Terminal
    E39 1 Ground No

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace harness.

CHECK FRONT AND REAR WASHER PUMP CIRCUIT 2

  1. Check continuity between front and rear washer pump harness connector and front and rear washer pump relay harness connector.

    Front and rear washer pump Front and rear washer pump relay Continuity
    Connector Terminal Connector Terminal
    E41 1 E39 6 Yes

  2. Check continuity between front and rear washer pump relay harness connector and ground.

    Front and rear washer pump relay (—) Continuity
    Connector Terminal
    E39 6 Ground No

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace harness.

CHECK REAR WASHER PUMP RELAY

Check rear washer pump relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Replace rear washer pump relay.

CHECK FRONT WASHER PUMP GROUND OPEN CIRCUIT

Check continuity between front and rear washer pump relay harness connector and ground.

Front and rear washer pump relay (—) Continuity
Connector Terminal
E39 10 Ground Yes

Is the inspection result normal?

YES>>

Replace front and rear washer pump. Refer to Removal and Installation.

NO>>

Repair or replace harness.

Component Inspection

CHECK FRONT WASHER PUMP RELAY

  1. Ignition switch OFF.

  2. Disconnect front washer pump relay connector.

  3. Check continuity between front washer pump relay terminals.

    Front washer pump relay Condition Continuity
    Terminals
    1 2 12 V direct current supply between terminals 3 and 4. Yes
    No current supply No
    5 12 V direct current supply between terminals 3 and 4. No
    No current supply Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace front washer pump relay.

    Dtc/circuit Diagnosis. Rear Wiper Motor Circuit
    Component Function Check CHECK REAR WIPER OPERATION CONSULT Select “Rear wiper” in "Active test" mode of "BCM". With operating the test item, check rear wiper operation. On ...
    Dtc/circuit Diagnosis. Rain and Light Sensor
    Component Function Check CHECK FRONT WIPER AUTO OPERATION Clean the rain and light sensor detection area of windshield fully. When the front wiper switch is turned to AUTO posit...

    Other materials:

    P0850 Pnp Switch
    DTC Description DESCRIPTIONTransmission range switch is turn ON when the selector lever is P or N.ECM detects the position because the continuity of the line (the ON) exists.DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0850 00 ...

    P2121 App Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2121 00 Throttle/pedal position sen/sw D (Throttle/Pedal Position Sensor/Switch "D" Circuit Range/Performance) Diagnosis condition Engine running at idle ...

    Diagnosis System (power Network Separate Relay)
    CONSULT Function (POWER NETWORK SEPARATE RELAY) APPLICATION ITEMSCONSULT performs the following functions via CAN communication using power network separate relay. Diagnosis mode Description Self Diagnostic Result Displays DTC stored in power network separate relay Displays freeze ...