Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Push-Button Ignition Switch Illumination Control Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Interior Lighting System / Dtc/circuit Diagnosis :: Push-Button Ignition Switch Illumination Control Circuit

Component Function Check

CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION

  1. With operating the push-button ignition switch, check that the push-button ignition switch illumination is turned ON/OFF.

    Push-button ignition switch ON : Push-button ignition switch illumination ON
    Push-button ignition switch OFF : Push-button ignition switch illumination OFF

Is the inspection result normal?

YES>>

Push-button ignition switch illumination control circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY 1

  1. Ignition switch OFF.

  2. Disconnect Intelligent Key unit connector and push-button ignition switch connector.

  3. Check continuity between Intelligent Key unit harness connector and ground.

    Intelligent Key unit — Continuity
    Connector Terminal
    M184 10 Ground No

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harnesses.

CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY 2

  1. Connect Intelligent Key unit connector and push-button ignition switch connector.

  2. Ignition switch ON.

  3. Check voltage between Intelligent Key unit harness connector and the ground.

    (+) (–) Condition

    Voltage

    (Approx.)
    Intelligent Key unit
    Connector Terminal
    M184 10 Ground Push-button ignition switch ON Battery voltage
    OFF 0 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace Intelligent Key unit. Refer to Removal and Installation.

CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect Intelligent Key unit connector and push-button ignition switch connector.

  3. Check continuity between Intelligent Key unit harness connector and push-button ignition switch harness connector.

    Intelligent Key unit Push-button ignition switch Continuity
    Connector Terminal Connector Terminal
    M184 10 M17 5 Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harnesses.

CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND CIRCUIT

Check continuity between push-button ignition switch harness connector and ground.

Push-button ignition switch — Continuity
Connector Terminal
M17 6 Ground Yes

Is the inspection result normal?

YES>>

Replace push-button ignition switch. Refer to Removal and Installation.

NO>>

Repair or replace harnesses.

    Dtc/circuit Diagnosis. Vanity Mirror Lamp Control Circuit
    Component Function Check CAUTION: Before performing the diagnosis, check that the following are normal: Interior room lamp power supply circuit Vanity mirror lamp bulb CHECK VAN...
    Symptom Diagnosis. Interior Lighting System Symptoms
    Symptom Table NOTE: Perform self diagnosis result with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected. Symptom Possible cause Inspect...

    Other materials:

    Exit Assist Function
    System Description SYSTEM DIAGRAMSeveral types of signals are transmitted from the following units to the driver seat control unit via CAN communication.INPUT SIGNAL AND OUTPUT SIGNAL Component Signal ABS actuator and electric unit (control unit) Nissan Ariya Vehicle speed signal BCM ...

    Kr15ddt. Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
    Noise, Vibration and Harshness (nvh) Troubleshooting With Idle Start/stop System NVH Troubleshooting Chart 1. Valve 2. Waterpump 3. Drive belt A. Camshaft bearing noise B. Piston pin noise C. Main bearing noise D. Piston slap noise E. Connecting ...

    U2143-57 Vcm/hpcm
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2143 57 CAN communication error (VCM/HPCM) Diagnosis condition — Signal (terminal) — Threshold MAC communication er ...