Nissan Rogue (T33) 2021-Present Service Manual: Vehicle Can Communication 2 Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / Vehicle Can Communication 2 Circuit

Diagnosis Procedure

CHECK NETWORK DIAGNOSIS

Check the "Network diagnosis" results from CONSULT to see that the Nissan Ariya vehicle CAN communication 4 circuit and diagnostic CAN communication circuit have no malfunction.

Are the Nissan Ariya vehicle CAN communication 4 circuit and diagnostic CAN communication circuit normal?

YES>>

GO TO 2.

NO>>

Check and repair Nissan Ariya vehicle CAN communication 4 circuit and/or diagnostic CAN communication circuit.

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the unit connectors on Nissan Ariya vehicle CAN communication 2 circuit.

  4. Check the terminals and connectors for damage, bend and loose connection (unit side and connector side).

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the BCM harness connector terminals.

  • With type B meter

    BCM harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    B26 87 E29 118 Existed
    86 117 Existed

  • With type A meter

    BCM harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    B123 104 E60 106 Existed
    103 107 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the BCM harness connector terminals.

  • With type B meter

    BCM harness connector Continuity
    Connector No. Terminal No.
    B26 87 86 Not existed

  • With type A meter

    BCM harness connector Continuity
    Connector No. Terminal No.
    B123 104 103 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the BCM and the ground.

  • With type B meter

    BCM harness connector Ground Continuity
    Connector No. Terminal No.
    B26 87 Not existed
    86 Not existed

  • With type A meter

    BCM harness connector Ground Continuity
    Connector No. Terminal No.
    B123 104 Not existed
    103 Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Check the harness and repair or replace the root cause.

CHECK BCM TERMINATION CIRCUIT

  1. Remove the BCM.

  2. Check the resistance between the BCM terminals.

    • With type B meter

      BCM Resistance (Ω)
      Terminal No.
      87 86 Approx. 108 – 132
      118 117 Approx. 108 – 132

    • With type A meter

      BCM Resistance (Ω)
      Terminal No.
      104 103 Approx. 108 – 132
      106 107 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 7.

NO>>

Replace the BCM.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 8.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of Nissan Ariya vehicle CAN communication circuit 2.

    NOTE:

    BCM has two termination circuits. Check other units first.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

    NOTE:

    Although unit-related error symptoms occur, do not confuse them with other symptoms.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

    Vehicle Can Communication 1 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the Nissan Ariya vehicle CAN communication 4 circuit and diagnostic CA...
    Vehicle Can Communication 4 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the ...

    Other materials:

    C1f00-54 Hands Off Threshold Incomplete
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F00 54 CONTROL UNIT (Control unit) Diagnosis condition — Signal (terminal) — Threshold Steering Torque C ...

    Engine oil
    Checking engine oil level Park the vehicle on a level area and apply the parking brake. Warm up the engine to operating temperature. Shut the engine off and wait at least 10 minutes. Remove the dipstick, wipe it clean, then fully reinsert it. Remove the dipstick again and check the oil le ...

    Automatic Brake Hold. Removal and Installation
    Chassis Control Module Removal and Installation Removal and installation procedure of chassis control module. Refer to Removal and Installation. Automatic Brake Hold Switch Removal and Installation Removal and installation procedure of parking brake switch. Refer to Removal and Installation.NOTE: ...