Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Rear Wiper Motor Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Wiper & Washer / Dtc/circuit Diagnosis :: Rear Wiper Motor Circuit

Component Function Check

CHECK REAR WIPER OPERATION

CONSULT

  1. Select “Rear wiper” in "Active test" mode of "BCM".

  2. With operating the test item, check rear wiper operation.

    On : Rear wiper operation
    Off : Stop the rear wiper

Is the inspection result normal?

YES>>

Rear wiper motor circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK REAR WIPER MOTOR OUTPUT VOLTAGE

  1. Rear wiper switch OFF.

  2. Ignition switch OFF.

  3. Disconnect rear wiper motor connector.

  4. Ignition switch ON.

  5. With operating rear wiper switch, check voltage between rear wiper motor harness connector and ground.

    (+) (−) Condition

    Voltage

    (Approx.)
    Rear wiper motor
    Connector Terminal
    D506 1 Ground Rear wiper switch ON Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK REAR WIPER MOTOR CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and rear wiper motor harness connector.

    With type A meter
    BCM Rear wiper motor Continuity
    Connector Terminal Connector Terminal
    B125 158 D506 1 Yes
    With type B meter
    BCM Rear wiper motor Continuity
    Connector Terminal Connector Terminal
    B27 148 D506 1 Yes

  4. Check continuity between BCM harness connector and ground.

    With type A meter
    BCM (—) Continuity
    Connector Terminal
    B125 158 Ground No
    With type B meter
    BCM (—) Continuity
    Connector Terminal
    B27 148 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK REAR WIPER MOTOR GROUND OPEN CIRCUIT

Check continuity between rear wiper motor harness connector and ground.

Rear wiper motor (—) Continuity
Connector Terminal
D506 3 Ground Yes

Is the inspection result normal?

YES>>

Replace rear wiper motor. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. Front Wiper Motor Ground Circuit
    Diagnosis Procedure CHECK FRONT WIPER MOTOR GROUND CIRCUIT Ignition switch OFF. Disconnect front wiper motor connector. Check continuity between front wiper motor harness connec...
    Dtc/circuit Diagnosis. Front Washer Circuit
    Component Function Check CHECK FRONT WASHER OPERATION When the front washer switch is turned to the ON position the front washer should operate. Is front washer operation normal...

    Other materials:

    Dtc/circuit Diagnosis. Unlock Sensor
    Diagnosis Procedure CHECK UNLOCK SENSOR INPUT SIGNAL Ignition switch OFF. Disconnect front door lock assembly LH connector. Check voltage between front door lock assembly LH harness connector and ground. (+) (–) Voltage (Approx.) Front door lock assembly LH Connector T ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...

    Admission Valve
    Component Inspection CHECK ADMISSION VALVE-1 With CONSULT Turn ignition switch ON (engine stopped). Perform “ADM/V motor target angle” in “Active Test” mode of “ENGINE” using CONSULT. Operate “Up” or “Down”, set “ADM/V Target Angle” to 0 deg, and check value ...