Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: P161d-00 Immobilizer

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Security Control System / Dtc/circuit Diagnosis :: P161d-00 Immobilizer

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC detecting condition
P161D-00

IMMOBILIZER

(Immobilizer) 		Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold When Intelligent Key unit detects an immobilizer malfunction and engine start is prohibited.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • ECM

  • Intelligent Key unit

  • Electric shift control module

  • Power steering control module

  • Improper key registration operation

  • Battery

FAIL-SAFE

Fuel cut

CONFIRMATION PROCEDURE

CHECK BATTERY CONDITION

Check battery condition. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace 12V battery. Refer to Removal and Installation.

CHECK DTC PRIORITY

If DTC P161D-00 is dsplayed with DTC U214F-87, B2033-4A, B2042-4A, B2043-4A, B2044-4A, B2045-4A, or B2047-87 first perform the trouble diagnosis for DTC U214F-87, B2033-4A, B2042-4A, B2043-4A, B2044-4A, B2045-4A, or B2047-87.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable DTC. U214F-87: DTC Description. B2033-4A: DTC Description. B2042-4A: DTC Description. B2043-4A: DTC Description. B2044-4A: DTC Description. B2045-4A: DTC Description. B2047-87: DTC Description.

NO>>

GO TO 3.

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of "ECM".

Is the DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK BATTERY CONDITION

Check battery condition. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace 12V battery. Refer to Removal and Installation.

CHECK DTC PRIORITY

If DTC P161D-00 is dsplayed with DTC U214F-87, B2033-4A, B2042-4A, B2043-4A, B2044-4A, B2045-4A, or B2047-87 first perform the trouble diagnosis for DTC U214F-87, B2033-4A, B2042-4A, B2043-4A, B2044-4A, B2045-4A, or B2047-87.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable DTC. U214F-87: DTC Description. B2033-4A: DTC Description. B2042-4A: DTC Description. B2043-4A: DTC Description. B2044-4A: DTC Description. B2045-4A: DTC Description. B2047-87: DTC Description.

NO>>

GO TO 3.

INTELLIGENT KEY REGISTRATION

  1. Perform registration of all Intelligent Keys using CONSULT.

    For registration procedures, refer to CONSULT immobilizer mode and follow the on-screen instructions.

  2. Erase DTC.

  3. Perform DTC confirmation procedure for DTC P161D-00. Refer to DTC Description.

Is DTC P161D-00 detected?

YES>>

GO TO 4.

NO>>

Inspection End.

CHECK ENGINE START

Ignition switch ON under the following conditions and wait 1 second or more:

  • Selector lever: In the P position or N position

  • Brake pedal: Depressed

Does the engine start?

YES>>

Clear DTC. Inspection End.

NO>>

GO TO 5.

REPLACE INTELLIGENT KEY UNIT

  1. Replace Intelligent Key unit. Refer to Removal and Installation.

  2. Erase DTC.

  3. Perform DTC confirmation procedure for DTC P161D-00. Refer to DTC Description.

  4. Check that the DTC is not detected.

>>

Inspection End.

    Basic Inspection. Additional Service When Replacing Ecm
    Description Performing the following procedure can automatically activate recommunication of ECM and Intelligent Key unit, but only when the ECM is replaced with a new one*. For...
    Dtc/circuit Diagnosis. P161e-00 Immobilizer
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition P161E-00 IMMOBILIZER (Immobilizer) Diagnosis condition Ignit...

    Other materials:

    Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses
    Work Flow CUSTOMER INTERVIEWInterview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of customer's comments; Refer to Diagnostic Work ...

    Accessory Relay
    Diagnosis Procedure CHECK ACCESSORY RELAY POWER SUPPLY Disconnect accessory relay connector. Check voltage between accessory relay harness connector and ground. (+) (–) Voltage (Approx.) Accessory relay Connector Terminal J-5 2 Ground Battery voltage 3 ...

    Valve Oil Seal
    Removal and Installation REMOVALRemove camshafts. Refer to Removal and Installation. Remove valve lifters. Refer to Exploded View. Rotate crankshaft and set piston that valve oil seal is to be removed to TDC. This will prevent valve from dropping into cylinder. CAUTION: When rotating cranksha ...