Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Map Lamp Control Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Interior Lighting System / Dtc/circuit Diagnosis :: Map Lamp Control Circuit

Component Function Check

CAUTION:

Before performing the diagnosis, check that the following are normal:

  • Interior room lamp power supply circuit

  • Each interior room lamp bulb

CHECK MAP LAMP OPERATION

CONSULT

  1. Switch the map lamp switch to DOOR.

  2. Open the front door LH.

  3. Ignition switch ON.

  4. Select “Interior lamp” in "Active test" mode of "BCM".

  5. With operating the test item, check that the map lamp turns ON/OFF.

    ON : Map lamp turns ON
    OFF : Map lamp turns OFF

Does the map lamp turn ON/OFF?

YES>>

Map lamp control circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK MAP LAMP CONTROL SIGNAL CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect map lamp assembly connector.

  3. Ignition switch ON.

  4. Check continuity between BCM harness connector and ground.

    With type A meter
    BCM — Condition Continuity
    Connector Terminal
    B124 131 Ground Front door LH Open Yes
    Close No
    With type B meter
    BCM — Condition Continuity
    Connector Terminal
    B23 130 Ground Front door LH Open Yes
    Close No

Is the inspection result normal?

YES>>

GO TO 2.

NO-1>>

Continuity Yes and remains unchanged: GO TO 4.

NO-2>>

Continuity No and remains unchanged: Replace BCM. Refer to Removal and Installation.

CHECK MAP LAMP CONTROL SIGNAL CIRCUIT 2

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and map lamp assembly harness connector.

    With type A meter
    BCM Map lamp assembly Continuity
    Connector Terminal Connector Terminal
    B124 131 R6 4 Yes
    With type B meter
    BCM Map lamp assembly Continuity
    Connector Terminal Connector Terminal
    B23 130 R6 4 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harnesses.

CHECK MAP LAMP GROUND CIRCUIT

Check continuity between map lamp assembly harness connector and ground.

Map lamp assembly — Continuity
Connector Terminal
R6 2 Ground Yes

Is the inspection result normal?

YES>>

Replace corresponding map lamp bulb. Refer to Replacement.

NO>>

Repair or replace harnesses.

CHECK MAP LAMP CONTROL SIGNAL CIRCUIT 3

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and ground.

    With type A meter
    BCM — Continuity
    Connector Terminal
    B124 131 Ground No
    With type B meter
    BCM — Continuity
    Connector Terminal
    B23 130 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harnesses.

    Dtc/circuit Diagnosis. Interior Room Lamp Power Supply Circuit
    Diagnosis Procedure Provides the interior room lamp power supply. Also cuts the power supply when the interior room lamp battery saver is activating.CHECK INTERIOR ROOM LAMP POW...
    Dtc/circuit Diagnosis. Room Lamp Control Circuit
    Component Function Check CAUTION: Before performing the diagnosis, check that the following are normal: Interior room lamp power supply circuit Map lamp control circuit Each int...

    Other materials:

    Affichages et témoins de ProPILOT
    Modèles avec affichage plein écran Modèles avec compteurs analogiques et affichage couleur ProPILOT Assist, ProPILOT Assist 1.1 Les affichages et témoins du système ProPILOT Assist du Nissan Rogue permettent au conducteur de comprendre en un coup d’œil l’état du système, les ...

    Dtc/circuit Diagnosis. Seat Memory Switch
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Memory switch 1”, “Memory switch 2” and “Set switch” in “Data monitor” mode of “DRIVER SEAT”. Check seat memory switch signal under the following conditions. Monitor item Conditio ...

    P00d2 Ho2s2 Heater
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P00D2 00 Heated O2 sensor heater B1 sensor 2 (HO2S heater control circuit range/performance bank 1 sensor 2) Diagnosis condition — Signal (terminal) ...