Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Room Lamp Control Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Interior Lighting System / Dtc/circuit Diagnosis :: Room Lamp Control Circuit

Component Function Check

CAUTION:

Before performing the diagnosis, check that the following are normal:

  • Interior room lamp power supply circuit

  • Map lamp control circuit

  • Each interior room lamp bulb

CHECK MAP LAMP OPERATION

  1. Switch the map lamp switch to DOOR.

  2. Check that the map lamp is turned ON when any door opens (except back door).

Is the inspection normal?

YES>>

GO TO 2.

NO>>

Check map lamp control circuit. Refer to Component Function Check.

CHECK ROOM LAMP OPERATION

CONSULT

  1. Switch the map lamp switch and room lamp switch to DOOR.

  2. Open the front door LH.

  3. Ignition switch ON.

  4. Select “Interior lamp” in "Active test" mode of "BCM".

  5. With operating the test item, check that the room lamp turns ON/OFF.

    ON : Room lamp turns ON
    OFF : Room lamp turns OFF

Does the room lamp turns ON/OFF?

YES>>

Room lamp control circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK ROOM LAMP CONTROL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect map lamp assembly connector and room lamp connector.

  3. Check continuity between map lamp assembly harness connector and room lamp harness connector.

    Map lamp assembly Room lamp Continuity
    Connector Terminal Connector Terminal
    R6 8 R15 2 Yes

  4. Check continuity between room lamp harness connector and ground.

    Room lamp — Continuity
    Connector Terminal
    R15 2 Ground No

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harnesses.

CHECK ROOM LAMP GROUND CIRCUIT

Check continuity between room lamp harness connector and ground.

Room lamp — Continuity
Connector Terminal
R15 3 Ground Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harnesses.

CHECK MAP LAMP CIRCUIT

Check continuity between map lamp assembly terminals.

Map lamp assembly Condition Continuity
Terminal
4 8 Map lamp switch is "DOOR" position Yes
Map lamp switch is "OFF" position No

Is the inspection result normal?

YES>>

Replace room lamp bulb. Refer to Replacement.

NO>>

Replace map lamp assembly. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. Map Lamp Control Circuit
    Component Function Check CAUTION: Before performing the diagnosis, check that the following are normal: Interior room lamp power supply circuit Each interior room lamp bulb CHEC...
    Dtc/circuit Diagnosis. Mood Lamp Control Circuit
    Component Function Check CAUTION: Before performing the diagnosis, check that the following are normal: Interior room lamp power supply circuit Mood lamp (center console) bulb (...

    Other materials:

    Removal and Installation. Floor Trim
    Exploded View ProPILOT Assist 2.1 Models 1. Rear floor carpet 2. Front floor carpet 3. Harness clip 4. Front floor spacer RH 5. Front floor spacer LH 6. Rear floor spacer center 7. Rear floor spacer         JAPAN PRODUCTION MODE ...

    Steering Switch Signal a Circuit
    Component Function Check PERFORM COMPONENT FUNCTION CHECK With CONSULT Check “Self Diagnostic Result” of “MULTI AV”. Is any DTC detected? YES>> Perform the trouble diagnosis for the detected DTC. Refer to DTC Index. NO>> Proceed to Diagnosis Procedure. Diagnosis Proced ...

    P026b Injection Timing
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P026B 00 Injection timing Diagnosis condition — Signal — Threshold ECM does not control fuel injection timing properly when engine is running ...