Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Luggage Room Lamp Control Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Interior Lighting System / Dtc/circuit Diagnosis :: Luggage Room Lamp Control Circuit

Component Function Check

CAUTION:

Before performing the diagnosis, check that the following are normal:

  • Interior room lamp power supply circuit

  • Luggage room lamp bulb

CHECK LUGGAGE ROOM LAMP OPERATION

CONSULT

  1. Ignition switch ON.

  2. Select “Trunk/luggage lamp” in "Active test" mode of "BCM".

  3. With operating the test item, check that the luggage room lamp turns ON/OFF.

    ON : Luggage room lamp ON
    OFF : Luggage room lamp OFF

Does luggage room lamp turn ON/OFF?

YES>>

Luggage room lamp control circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK LUGGAGE ROOM LAMP CONTROL SIGNAL

CONSULT

  1. Ignition switch OFF.

  2. Disconnect luggage room lamp connector.

  3. Ignition switch ON.

  4. Select "Trunk/luggage lamp" in "Active test" mode of "BCM".

  5. With operating the test item, check continuity BCM harness connector and ground.

    With type A meter
    BCM (—) Test item Continuity
    Connector Terminal
    M51 21 Ground Trunk/luggage lamp ON Yes
    OFF No
    With type B meter
    BCM (—) Test item Continuity
    Connector Terminal
    M18 30 Ground Trunk/luggage lamp ON Yes
    OFF No

Is the inspection result normal?

YES>>

GO TO 2.

NO-1>>

Continuity exists and remains unchanged: GO TO 4.

NO-2>>

Continuity does not exist and remains unchanged: Replace BCM. Refer to Removal and Installation.

CHECK LUGGAGE ROOM LAMP CONTROL SIGNAL CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and luggage room lamp harness connector.

    With type A meter
    BCM Luggage room lamp Continuity
    Connector Terminal Connector Terminal
    M51 21 R23 1 Yes
    With type B meter
    BCM Luggage room lamp Continuity
    Connector Terminal Connector Terminal
    M18 30 R23 1 Yes

  4. Check continuity between luggage room lamp harness connector and ground.

    Luggage room lamp (—) Continuity
    Connector Terminal
    R23 1 Ground No

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harnesses.

CHECK LUGGAGE ROOM LAMP GROUND CIRCUIT

Check continuity between luggage room lamp harness connector and ground.

Luggage room lamp — Continuity
Connector Terminal
R23 1 Ground Yes

Is the inspection result normal?

YES>>

Replace luggage room lamp bulb. Refer to Replacement.

NO>>

Repair or replace harnesses.

CHECK LUGGAGE ROOM LAMP CONTROL SIGNAL CIRCUIT 2

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and ground.

    With type A meter
    BCM (—) Continuity
    Connector Terminal
    M51 21 Ground No
    With type B meter
    BCM (—) Continuity
    Connector Terminal
    M18 30 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harnesses.

    Dtc/circuit Diagnosis. Mood Lamp Control Circuit
    Component Function Check CAUTION: Before performing the diagnosis, check that the following are normal: Interior room lamp power supply circuit Mood lamp (center console) bulb (...
    Dtc/circuit Diagnosis. Vanity Mirror Lamp Control Circuit
    Component Function Check CAUTION: Before performing the diagnosis, check that the following are normal: Interior room lamp power supply circuit Vanity mirror lamp bulb CHECK VAN...

    Other materials:

    Meters and gauges
    MODELS WITH ANALOG METER AND COLOR DISPLAY Tachometer Warning and indicator lights Vehicle information display Odometer Speedometer Engine coolant temperature gauge Fuel gauge CAUTION For cleaning, use a soft cloth dampened with water. Never use a rough cloth, alcohol, benzine, thi ...

    B2e49-06 Remote Actuator
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2E49–06 Remote actuator not activated (Remote actuator not activated) Diagnosis condition When receiving remote command Signal (terminal) — Thresh ...

    Variable Compression Ratio Control Shaft 2 Rotation Angle Sensor
    Component Inspection CHECK VCR CONTROL SHAFT 2 ROTATION ANGLE SENSOR Turn ignition switch OFF. Disconnect VCR control shaft 2 rotation angle sensor harness connector. Check the continuity between VCR control shaft 2 rotation angle sensor harness connectors. VCR control shaft 2 rota ...