Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Lifting Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Lifting switch (Up)� and “Lifting switch (Down)� in “Data monitor� mode of “DRIVER SEAT�.

  3. Check lifting switch signal under the following conditions.

Monitor item Condition Status
Lifting switch (Up) Lifting switch Operate (upward) On
Release Off
Lifting switch (Down) Lifting switch Operate (downward) On
Release Off

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK LIFTING SWITCH POWER SUPPLY VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector.

  3. Ignition switch ON.

  4. Check voltage between power seat switch LH harness connector and ground.

    (+) (-)

    Voltage

    (Approx.)
    Power seat switch LH
    Connector Terminal
    B215 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK LIFTING SWITCH SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect driver seat control unit connector.

  3. Check continuity between power seat switch LH harness connector and driver seat control unit harness connector.

    Power seat switch LH Driver seat control unit Continuity
    Connector Terminal Connector Terminal
    B215 1 B213 31 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK LIFTING SWITCH SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between power seat switch LH harness connector and ground.

Power seat switch LH (—) Continuity
Connector Terminal
B215 1 Ground No

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK LIFTING SWITCH

Check lifting switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

Component Inspection

CHECK LIFTING SWITCH

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector.

  3. Check resistance between power seat switch LH terminals.

    Power seat switch LH Condition Resistance: kΩ
    Terminals
    1 4 Lifting switch Operate (upward) 0.418 – 0.426
    Operate (downward) 0.258 – 0.264
    Release 29.700 – 30.300

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. Reclining Sensor
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Reclining motor position� in “Data monitor� mode of “DRIVER SEAT�. Check reclining sensor...
    Dtc/circuit Diagnosis. Seat Memory Switch
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Memory switch 1�, “Memory switch 2� and “Set switch� in “Data monitor� mode of “DRI...

    Other materials:

    Rear sunshade
    CAUTION Do not release the rear sunshade during operation. This could damage the sunshade or cause injury. Do not forcefully pull the sunshade. Doing so may elongate the sunshade, leading to improper operation or damage. Do not place objects on or near the rear sunshade as this may int ...

    Lower Anchors and Tethers for CHildren (LATCH) system
    LATCH system anchor location Basic information Your Nissan Rogue includes special anchor points for LATCH-compatible child restraints. This system may also be called ISOFIX. With LATCH, you do not need to use the seat belt unless the combined weight of the child plus restraint exceeds 65 lbs ( ...

    Can Fundamental. Description
    Outline How to Use This Section “CAN FUNDAMENTAL� of LAN Section describes the basic knowledge of the CAN communication system and the method of trouble diagnosis. For information peculiar to a Nissan Ariya vehicle and inspection procedure, refer to “CAN�. System (can Commun ...