Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Front Wiper Motor Lo Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Wiper & Washer / Dtc/circuit Diagnosis :: Front Wiper Motor Lo Circuit

Component Function Check

CHECK FRONT WIPER LO OPERATION

CONSULT

  1. Select “Front wiper” in “Active test” mode of “BCM [WIPER]”.

  2. With operating the test item, check front wiper operation.

    Low : Front wiper (LO) operation
    Off : Stop the front wiper

Is the inspection result normal?

YES>>

Front wiper motor LO circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect front wiper motor connector.

  3. Ignition switch ON.

  4. Turn front wiper switch to LOW.

  5. Check voltage between front wiper motor harness connector and ground.

    (+) (−) Condition

    Voltage

    (Approx.)
    Front wiper motor
    Connector Terminal
    E20 3 Ground Front wiper switch Lo

    Battery voltage

    (10 seconds*)

*: According to front wiper protection function, IPDM E/R supplies voltage for 10 seconds (battery voltage) and then stops for 20 seconds (no voltage). This operation occurs repeatedly.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK FRONT WIPER MOTOR (LO) CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.

    IPDM E/R Front wiper motor Continuity
    Connector Terminal Connector Terminal
    E121 48 E20 3 Yes

  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R (—) Continuity
    Connector Terminal
    E121 48 Ground No

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation

NO>>

Repair or replace harness.

CHECK FRONT WIPER MOTOR GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect front wiper motor connector.

  3. Check continuity between front wiper motor harness connector and ground.

    Front wiper motor (—) Continuity
    Connector Terminal
    E20 2 Ground Yes

Is the inspection result normal?

YES>>

Replace front wiper motor. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2cb5-64 Rear Wiper
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2CB5–64 Rear wiper (Rear wiper) Diagnosis condition When ...
    Dtc/circuit Diagnosis. Front Wiper Auto Stop Signal Circuit
    Component Function Check CHECK FRONT WIPER STOP POSITION SIGNAL CONSULT Select “FR WIPER STOP POSITION” in “Data monitor” mode of “IPDM E/R”. Operate the front wiper...

    Other materials:

    Dtc/circuit Diagnosis. Door Lock Actuator
    Front Lh Diagnosis Procedure CHECK DOOR LOCK ACTUATOR INPUT SIGNAL Ignition switch OFF. Disconnect front door lock assembly LH connector. Check voltage between front door lock assembly LH harness connector and ground. (+) (–) Condition Voltage (Approx.) Front door lock a ...

    Lane Change Assist
    Basic information Lane Change Assist is a feature of ProPILOT Assist 2.1 on the Nissan Rogue. Read the entire ProPILOT Assist section before using this system, including how to operate it and how to interpret the display. When ProPILOT Assist is active and the status indicator A is illuminated in ...

    Dtc/circuit Diagnosis. Power Supply and Ground Circuit. Sonar Control Unit
    Sonar Control Unit Diagnosis Procedure CHECK FUSE Check that the following fuse is not blown (open). Power source Fuse No. Capacity ACC power supply #40 10 A Is the fuse blown (open)? YES>> Be sure to eliminate cause of malfunction before installing new fuse. NO>&g ...