Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Back Door Opener Switch

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: Back Door Opener Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Request switch back door/trunk lid” in “Data monitor” mode of "BCM [TRUNK]".

  3. Check that the function operates normally according to the following conditions.

Monitor item Condition Status
Request switch door/trunk lid Back door opener switch Pressed On
Released Off

Is the inspection result normal?

YES>>

Back door opener switch is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK BACK DOOR OPEN INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect back door opener switch connector.

  3. Check voltage between back door opener switch harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Back door opener switch
    Connector Terminal
    D507 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK BACK DOOR OPENER SWITCH CIRCUIT

  1. Disconnect BCM connector.

  2. Check continuity between BCM harness connector and back door opener switch harness connector.

    BCM Back door opener switch Continuity
    Connector Terminal Connector Terminal
    B26 (with type B meter) 98 D507 1 Yes
    B123 (with type A meter) 93

  3. Check continuity between BCM harness connector and ground.

    BCM — Continuity
    Connector Terminal
    B26 (with type B meter) 98 Ground No
    B123 (with type A meter) 93

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK BACK DOOR OPENER SWITCH GROUND CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Back door opener switch — Continuity
Connector Terminal
D507 2 Ground Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK BACK DOOR OPENER SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace back door opener switch. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

Component Inspection

CHECK BACK DOOR OPENER SWITCH

  1. Ignition switch OFF.

  2. Disconnect back door opener switch connector.

  3. Check continuity between back door opener switch terminals.

    Back door opener switch Condition Continuity
    Terminal
    1 2 Back door opener switch Pressed Yes
    Released No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace back door opener switch. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. Back Door Opener Actuator
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Trunk/back door” in “Active test” mode of "BCM". Check that the function operates normally ac...
    Dtc/circuit Diagnosis. Back Door Request Switch
    Component Inspection CHECK BACK DOOR REQUEST SWITCH Ignition switch OFF. Disconnect back door opener switch connector. Check back door opener switch terminals. Back door opener ...

    Other materials:

    P2123 App Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2123 00 APP SEN 1/CIRC (Throttle/Pedal position sensor/switch D circuit high) Diagnosis condition Engine running at idle Signal (terminal) Accelerator ...

    Dtc/circuit Diagnosis. Drive Mode Select Switch Circuit
    Diagnosis Procedure CHECK DRIVE MODE SELECT SWITCH SIGNAL CIRCUIT Ignition switch OFF. Disconnect drive mode select switch harness connector and BCM harness connector. Check the continuity between drive mode select switch harness connector and BCM harness connector. 2WD models with ...

    Engine oil
    Checking engine oil level Park the vehicle on a level area and apply the parking brake. Warm up the engine to operating temperature. Shut the engine off and wait at least 10 minutes. Remove the dipstick, wipe it clean, then fully reinsert it. Remove the dipstick again and check the oil le ...