Nissan Rogue (T33) 2021-Present Service Manual: P05ec Cold Start Control

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P05ec Cold Start Control

DTC Description

ECM controls fuel injection timing and fuel injection quantity when engine is started with the engine cold.

This control promotes the activation of three way catalyst by heating the catalyst and reduces emissions.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P05EC 00

COLD START CONTROL

(COLD START CONTROL) 		Diagnosis condition —
Signal (terminal) —
Threshold ECM does not control fuel injection timing properly when engine is started with the engine cold
Diagnosis delay time —

POSSIBLE CAUSE

ECM

FAIL-SAFE

Not applicable

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P05EC is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Select “DATA MONITOR” mode of “ENGINE” using CONSULT.

  4. Check that “COOLANT TEMP/S”.

    • If it is between 5°C (41°F) and 40°C (104°F) go to the following steps.

    • If it is below 5°C (41°F) warm engine up to more than 5°C (41°F) and retry from step 1.

    • If it is above 40°C (104°F) cool engine down to less than 40°C (104°F) and retry from step 1.

  5. Start engine and let it idle for 5 minutes.

  6. Check 1st trip DTC.

With GST

Follow the procedure “With CONSULT” above.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P05EC is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

INSPECTION START

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure. Refer to DTC Description.

  4. Check 1st trip DTC.

Is the 1st trip DTC P05EC displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P059f Active Grille Shutter
    DTC Description DTC DETECTION LOGICActive grille shutter normally stops within zone which is defined by zone (90°±10°).If the active grille shutter stops within zone stuck er...
    P0604 Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0604 00 ECM [Internal control module random access memory (RAM)...

    Other materials:

    Automatic air conditioner (models with rear control)
    Basic information Temperature control dial (driver's side) AUTO button Air recirculation button Outside air button Display screen SYNC button Temperature control dial (passenger's side) ON·OFF button Rear temperature control buttons Fan speed buttons Air flow button Front defr ...

    Dtc/circuit Diagnosis. B2906-11 Recliner Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B2906-11 Recliner Sensor Diagnosis condition The Recliner Sensor signal is shorted to ground Signal (terminal) Reclining Motor (terminal #5) Threshold ...

    P0053 A/f Sensor 1 Heater
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0053 00 HO2S1 HTR B1 (HO2S heater resistance bank 1 sensor 1) Diagnosis condition — Signal (terminal) A/F sensor 1 heater signal Threshold D ...