Nissan Rogue (T33) 2021-Present Service Manual: P059f Active Grille Shutter

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P059f Active Grille Shutter

DTC Description

DTC DETECTION LOGIC

Active grille shutter normally stops within zone which is defined by zone (90°±10°).

If the active grille shutter stops within zone stuck error is detected, and if the active grille shutter stops at position beyond zone overrun error is detected.

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P059F 00

ACTIVE GRILLE AIR SHUTTER A

(Active grille air shutter A performance/stuck off) 		Diagnosis condition —
Signal (terminal) Active grille shutter communication signal
Threshold Detects the malfunction of initial position learning or operational malfunctions for specified times.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (Active grille shutter circuit is open or shorted.)

  • Active grille shutter

  • Foreign objects interferes with active grille shutter

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P059F is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM DIAGNOSIS PROCEDURE

NOTE:

Since this DTC is difficult to be confirmed, perform diagnosis procedure to judge the normality.

>>

Refer to DTC Diagnosis Procedure.

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P059F is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ACTIVE GRILL SHUTTER

  1. Turn ignition switch OFF.

  2. Check if any foreign objects interferes with active grille shutter.

  3. Check the installation condition of active grille shutter.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY

  1. Disconnect active grille shutter harness connector.

  2. Check the voltage between active grille shutter harness connector and ground as follows.

    + − Condition

    Voltage

    (Approx.)
    Active grille shutter
    Connector Terminal
    E46 1 Ground Ignition switch: ON Battery voltage
    Ignition switch: OFF 0 V

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between active grille shutter harness connector and IPDM E/R harness connector.

    Active grille shutter IPDM E/R Continuity
    Connector Terminal Connector Terminal
    E46 1 E119 8 Existed

Is the inspection result normal?

YES>>

Perform trouble diagnosis for power supply circuit.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER GROUND CIRCUIT

  1. Turn ignition switch OFF

  2. Check the continuity between active grille shutter harness connector and ground.

    Active grille shutter − Continuity
    Connector Terminal
    E46 4 Ground Existed

  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK ACTIVE GRILLE SHUTTER INPUT SIGNAL CIRCUIT

  1. Disconnect ECM harness connector.

  2. Check the continuity between ECM harness connector and active grille shutter harness connector.

+ – Continuity
ECM Active grille shutter
Connector Terminal Connector Terminal
F72 21 E46 3 Existed

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER

Check active grille shutter. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace active grille shutter. Refer to Removal and Installation.

    P0573 Brake Pedal Switch a
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0573 Brake pedal switch A (Brake Switch "A" Circuit High) Diagn...
    P05ec Cold Start Control
    DTC Description ECM controls fuel injection timing and fuel injection quantity when engine is started with the engine cold.This control promotes the activation of three way cata...

    Other materials:

    P2a01 Ho2s2
    DTC Description The heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of the three way catalyst (manifold) causes the longer switching time.MALFUNCTION ATo judge the malfunctions of heated oxygen ...

    Removal and Installation. Body Side Trim
    Exploded View With ProPILOT Assist 2.1 1. Rear body side welt 2. Bolt cap 3. Center pillar upper garnish 4. Front body side welt 5. Front pillar garnish 6. Dash side finisher RH 7. Front kicking plate 8. Harness protector 9. Center pillar lower ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...