Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2436-13 Spindle Motor Lh

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2436-13 Spindle Motor Lh

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2436-13

Spindle motor LH

(Spindle motor left hand) 		Diagnosis condition All times
Signal (terminal) Spindle motor LH signal
Threshold Automatic back door control unit cannot detect the spindle motor LH signal
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (spindle motor LH circuit is open)

  • Automatic back door control unit

  • Spindle unit LH

FAIL-SAFE

Inhibit automatic back door system (only operate back door closure function)

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK SPINDLE MOTOR INPUT SIGNAL

Check signal between spindle unit LH harness connector and ground using oscilloscope.

(+) (–) Condition

Signal

(Reference value)

(Approx.)
Spindle unit LH
Connector Terminal
B95 1 Ground Back door Auto open operation

Auto close operation 0 – 1 V
7 Auto close operation

Auto open operation 0 – 1 V

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK SPINDLE MOTOR CIRCUIT

  1. Disconnect automatic back door control unit connector and spindle unit LH connector.

  2. Check continuity between automatic back door control unit harness connector and spindle unit LH harness connector.

    Automatic back door control unit Spindle unit LH Continuity
    Connector Terminal Connector Terminal
    B56 38 B95 1 Yes
    39 7

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B56 38 Ground No
    39

Is the inspection result normal?

YES>>

Replace spindle unit LH. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2436-12 Spindle Motor Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2436-12 Spindle motor LH (Spindle motor left hand) Diagnosi...
    Dtc/circuit Diagnosis. B2436-19 Spindle Motor Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2436-19 Spindle motor LH (Spindle motor left hand) Diagnosi...

    Other materials:

    B2e01-96 Tcu
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2E01-96 Internal battery (Internal battery) Diagnosis condition When ignition switch is ON Signal (terminal) Internal battery Threshold Internal ba ...

    Power Supply and Ground Circuit
    Ecm Diagnosis Procedure CHECK THE BATTERY CABLE Turn ignition switch OFF. Check the battery cable for tightening enough. NOTE: Check the continuity between the battery cable and the battery terminal. Is the inspection result normal? YES>> GO TO 2 ...

    Door Lock Function
    System Description SYSTEM DIAGRAMDoor lock function controls operation function of the following items. Door lock and unlock function (door request switch) Selective unlock function (door request switch) Reminder function (door request switch) Auto door lock function (door request ...