Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2436-19 Spindle Motor Lh

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2436-19 Spindle Motor Lh

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2436-19

Spindle motor LH

(Spindle motor left hand) 		Diagnosis condition All times
Signal (terminal) Spindle motor LH signal
Threshold When automatic back door control unit detect over current (15 A or more) of spindle motor LH circuit
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (spindle motor LH circuit is power short)

  • Automatic back door control unit

  • Spindle unit LH

FAIL-SAFE

Inhibit automatic back door system (only operate back door closure function)

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK SPINDLE MOTOR INPUT SIGNAL

Check signal between spindle unit LH harness connector and ground using oscilloscope.

(+) (–) Condition

Signal

(Reference value)

(Approx.)
Spindle unit LH
Connector Terminal
B95 1 Ground Back door Auto open operation

Auto close operation 0 – 1 V
7 Auto close operation

Auto open operation 0 – 1 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor RH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector, securely lock the connector, and GO TO 5.

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor RH harness connector and check touch sensor RH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

CHECK SPINDLE MOTOR CIRCUIT

  1. Disconnect automatic back door control unit connector and spindle unit LH connector.

  2. Check voltage between automatic back door control unit harness connector and ground.

    Automatic back door control unit —

    Voltage

    (Approx.)
    Connector Terminal
    B56 38 Ground 0 V
    39

Is the inspection result normal?

YES>>

Replace spindle unit LH. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2436-13 Spindle Motor Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2436-13 Spindle motor LH (Spindle motor left hand) Diagnosi...
    Dtc/circuit Diagnosis. B2436-98 Spindle Motor Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2436-98 Spindle motor LH (Spindle motor left hand) Diagnosi...

    Other materials:

    Dtc/circuit Diagnosis. C161b-86 Abs System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C161B 86 ABS system (Anti-lock braking system ) Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold ...

    B2e01-96 Tcu
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2E01-96 Internal battery (Internal battery) Diagnosis condition When ignition switch is ON Signal (terminal) Internal battery Threshold Internal ba ...

    Dtc/circuit Diagnosis. P161d-00 Immobilizer
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition P161D-00 IMMOBILIZER (Immobilizer) Diagnosis condition Ignition switch ON Signal (terminal) — Threshold When Intelligent Key unit detects an immob ...