Nissan Rogue (T33) 2021-Present Service Manual: B2e01-96 Tcu

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Audio, Visual & Navigation System / Telematics System :: Dtc/circuit Diagnosis / B2e01-96 Tcu

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
B2E01-96

Internal battery

(Internal battery) 		Diagnosis condition When ignition switch is ON
Signal (terminal) Internal battery
Threshold Internal battery abnormality
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Internal battery disconnected

  • Internal battery abnormality

  • Internal battery connector error

FAIL-SAFE

Telematics system does not operate

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Turn ignition switch OFF and wait at least 30 seconds.

  3. Turn ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “IVC” using CONSULT.

  5. Check DTC.

Is DTC B2E01-96 detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC STATUS

Check if DTC B2E01-96 is "CRNT" or "PAST".

Is DTC B2E01‐96 "CRNT"?

YES>>

GO TO 2.

NO>>

GO TO 4.

PERFORM WORK SUPPORT

With CONSULT

Perform "TCU Backup Battery Reset" in "Work Support".

>>

GO TO 3.

PERFORM SELF DIAGNOSTIC RESULT

With CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select "Self Diagnostic Result" mode of "IVC".

  5. Check DTC.

Is DTC B2E01-96 "CRNT" detected again?

YES>>

GO TO 4.

NO>>

Inspection End.

PERFORM CONFIRMATION PROCEDURE AGAIN

With CONSULT

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform confirmation procedure again. Refer to DTC Description.

Is DTC B2E01‐96 detected?

YES>>

Replace TCU. Refer to Removal & Installation.

NO>>

Refer to Intermittent Incident.

    B2e01-4a Tcu
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2E01-4A Internal battery (Internal battery) Diagnosis condi...
    B2e08-01 Microphone
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2E08–01 Microphone (Microphone) 1 Diagnosis condition Whe...

    Other materials:

    Basic Inspection. System Initialization
    Description Initialization of system should be conducted after the following conditions: Refer to Work Procedure. When the moonroof motor assembly or sunshade motor assembly is replaced. When the moonroof or sunshade does not operate normally. (Incomplete initialization conditions) Wor ...

    Dtc/circuit Diagnosis. B2c95-64 Combination Switch
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2C95-64 Combination switch (Combination switch) Diagnosis condition Ignition switch OFF (auto ACC status) Signal (terminal) Combination switch signal ...

    P2b95 Cold Start Control
    DTC Description ECM controls fuel injection timing and fuel injection quantity when engine is started with the engine cold.This control promotes the activation of three way catalyst by heating the catalyst and reduces emissions.DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis co ...