Nissan Rogue (T33) 2021-Present Service Manual: Calibration of Side G Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Basic Inspection / Calibration of Side G Sensor

Description

CAUTION:

Always perform the side G sensor calibration before driving when the following operation is performed. Refer to Work Procedure.

×: Required —: Not required

Procedure Side G sensor calibration
Removing/ installing ABS actuator and electric unit (control unit) ×
Replacing ABS actuator and electric unit (control unit) ×
Removing/installing steering components —
Replacing steering components —
Removing/installing front suspension components —
Replacing front suspension components —
Removing/installing tire —
Replacing tire —
Tire rotation —
Adjusting front wheel alignment. —

Work Procedure

CAUTION:

Always use CONSULT for the side G sensor calibration. (It cannot be adjusted other than CONSULT.)

CHECK THE VEHICLE STATUS

  1. Steer the steering wheel to the straight-ahead position. Stop the Nissan Ariya vehicle on level surface.

  2. Stop the engine.

  3. Ignition switch OFF (Auto ACC function OFF).

Is the Nissan Ariya vehicle stopped in the straight-ahead position on level surface?

YES>>

GO TO 2.

NO>>

Steer the steering wheel to the straight-ahead position. Stop the Nissan Ariya vehicle on level surface.

PERFORM SIDE G SENSOR CALIBRATION

CAUTION:

  • Never allow passenger or load on the Nissan Ariya vehicle.

  • Never apply vibration to the vehicle body when opening or closing door during calibration.

CONSULT

  1. Ignition switch ON.

    CAUTION:

    Never start engine.

  2. Select “ABS”, “Work support”, “DECEL G SENSOR CALIBRATION” in this order.

  3. Select “START”.

  4. After approximately 10 seconds, select “END”.

  5. Ignition switch OFF (Auto ACC function OFF) and then it ON again.

    CAUTION:

    Be sure to perform the operation above.

>>

GO TO 3.

CHECK Data monitor

CONSULT

  1. Drive the Nissan Ariya vehicle. Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.

  2. Select “ABS”, “Data monitor”, and “Side G sensor” in this order. Check that the signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

CONSULT

Erase self-diagnosis result of all systems.

Are the memories erased?

YES>>

Inspection End

NO>>

Check the items indicated by the self-diagnosis.

    Calibration of Decel G Sensor
    Description CAUTION: Always perform the decel G sensor calibration before driving when the following operation is performed. Refer to Work Procedure. ×: Required —: Not requi...
    Adjustment of Brake Caliper Initial Position
    Description CAUTION: When performing the following operations, always use CONSULT (It cannot be performed by any means other than CONSULT.), for performing "INITIALIZATION POSIT...

    Other materials:

    Engine Stand Setting
    Setting NOTE: Explained here is how to disassemble with engine stand supporting transaxle surface. When using different type of engine stand, note with difference in steps and etc. Remove the engine and the transaxle assembly from the vehicle, and separate the transaxle from the engine. Ref ...

    P1c90-49 Sub Starter & Generator
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1C90-49 Sub starter & generator (Sub starter & generator) Diagnosis condition Engine running at idle Signal (terminal) - Threshold Sub starte ...

    B2730-13 Side Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2730-13 SIDE SENSOR [RL] (Side sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH side Threshold H ...