Nissan Rogue (T33) 2021-Present Service Manual: C1f04-48 Feb Ope Count Limit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Adas Control Unit :: Dtc/circuit Diagnosis / C1f04-48 Feb Ope Count Limit

Without Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
C1F04 48

FEB OPE COUNT LIMIT

(Forward Emergency Braking operation count limit) 		Diagnosis condition When engine is running
Signal (terminal) —
Threshold AEB system operated 3 times within ignition switch ON.
Diagnosis delay time 1 second or less

NOTE:

If “C1F04-48” detected, perform the AEB system action test and AEB system operates normally.

POSSIBLE CAUSE

AEB system operated 3 times within ignition switch ON.

FAIL-SAFE

The following systems are canceled.

  • AEB

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C1F04-48” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “C1F04-48” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

With Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
C1F04 48 FEB OPERATION COUNT LIMIT Diagnosis condition When engine is running
Signal (terminal) —
Threshold FEB system operated 3 times within ignition switch ON.
Diagnosis delay time 1 second or less

NOTE:

If “C1F04-48” detected, perform the FEB system action test and FEB system operates normally.

POSSIBLE CAUSE

FEB system operated 3 times within ignition switch ON.

FAIL-SAFE

The following systems are canceled.

  • Lane keep function*

  • Lane change support function

  • Overtaking support function

  • Route driving support function

  • FEB

  • RAB

  • PFCW

  • TSR

*: ProPILOT Assist 2.1 display is blue

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C1F04-48” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “C1F04-48” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair:Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK SELF-DIAGNOSIS RESULTS

  1. Turn ignition switch OFF.

  2. Turn ignition switch ON.

  3. Perform “All DTC Reading” with CONSULT.

  4. Check if any DTC other than “C1F04-48” is detected in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is any DTC detected?

YES>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

NO>>

Perform the distance sensor alignment. Refer to Work Procedure .

    C1f03-73 Stop Lamp Relay
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F03 73 OPERATION SW CIRC (O...
    C1f04-61 Brake Sw/stop Lamp Sw
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F04 61 FEB OPE COUNT LIMIT ...

    Other materials:

    Dtc/circuit Diagnosis. B1000-49 Air Bag Diagnosis Sensor Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1000-49 Air bag diagnosis sensor unit (Air bag diagnosis sensor unit) Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold ...

    Vdc Off Indicator Lamp
    Component Function Check CHECK VDC OFF INDICATOR LAMP FUNCTION (1) Check that VDC OFF indicator lamp in combination meter turns ON for approximately 1 second after ignition switch is ON. CAUTION: Never start engine. Is the inspection result normal? YES>> GO TO 2. NO>> Refer ...

    Accelerator Pedal Released Position Learning
    Description Accelerator Pedal Released Position Learning is a function of ECM to learn the fully released position of the accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time harness connector of accelerator pedal position senso ...