Nissan Rogue (T33) 2021-Present Service Manual: C1f03-73 Stop Lamp Relay

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Adas Control Unit :: Dtc/circuit Diagnosis / C1f03-73 Stop Lamp Relay

Without Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
C1F03 73

OPERATION SW CIRC

(Operation switch circuit) 		Diagnosis condition

  • When engine is running

  • When AEB system is ON
Signal (terminal) —
Threshold Stop lamp inactive state despite the outputting of a stop lamp request signal from ADAS control unit 2
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • BCM

  • ADAS control unit 2

FAIL-SAFE

The following systems are canceled.

  • Vehicle-to-vehicle distance control mode

  • Conventional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • RAB

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C1F03-73” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Turn the AEB system ON

  3. Perform “All DTC Reading”.

  4. Check if the “C1F03-73” is detected as the current malfunction in the “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “C1F03-73” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C1F03-73” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS OF BCM

Check if any DTC is detected in “Self Diagnostic Result” of “BCM”.

Is any DTC detected?

YES>>

Repair or replace the malfunctioning parts identified by the self-diagnosis result. Refer to DTC Index.

NO>>

Replace ADAS control unit 2. Refer to Removal and Installation.

With Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
C1F03 73 OPERATION SW CIRCUIT Diagnosis condition When engine is running
Signal (terminal) Stop lamp request signal
Threshold Stop lamp inactive state despite the outputting of a stop lamp request signal from ADAS control unit 2
Diagnosis delay time 60 seconds or more

POSSIBLE CAUSE

BCM

FAIL-SAFE

The following systems are canceled.

  • Vehicle speed & vehicle-to-vehicle control function

  • Lane keep function*1

  • Lane keep function*2

  • Lane change support function

  • Overtaking support function

  • Route driving support function

  • FEB

  • RAB

  • PFCW

  • LDP

  • Blind Spot Intervention

  • TSR

  • DAA

*1: ProPILOT Assist 2.1 display is green

*2: ProPILOT Assist 2.1 display is blue

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C1F03-73” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

NOTE:

To prevent the possibility of accident, perform component function check instead of DTC confirmation procedure.

  1. Start the engine.

  2. Perform the active test items “STOP LAMP 1” and “STOP LAMP 2” of “BCM” with CONSULT.

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Refer to DTC Diagnosis Procedure.

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C1F03-73” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable.Refer to DTC Index.

NO>>

GO TO 2.

CHECK BCM SELF-DIAGNOSTIC RESULT

CONSULT

Check if any DTC is detected in “Self Diagnostic Result” mode of “BCM”.

Is any DTC detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

GO TO 3.

CHECK ADAS CONTROL UNIT 2 SELF-DIAGNOSTIC RESULT

Check if any DTC is detected in “Self Diagnostic Result” mode of “ICC/ADAS 2”.

Is any DTC detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

    C1f03-72 Stop Lamp Relay
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F03 72 OPERATION SW CIRC (O...
    C1f04-48 Feb Ope Count Limit
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F04 48 FEB OPE COUNT LIMIT ...

    Other materials:

    Crankshaft Position Sensor
    Component Inspection CHECK CRANKSHAFT POSITION SENSOR (POS)-1 Turn ignition switch OFF. Loosen the fixing bolt of the sensor. Disconnect crankshaft position sensor (POS) harness connector. Remove the sensor. Visually check the sensor for chipping. Is the inspection r ...

    Dtc/circuit Diagnosis. Push-Button Ignition Switch Illumination Control Circuit
    Component Function Check CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION With operating the push-button ignition switch, check that the push-button ignition switch illumination is turned ON/OFF. Push-button ignition switch ON : Push-button ignition switch illumination ON Pus ...

    Laser Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side). Distance sensor Harness connector B2 ...