Nissan Rogue (T33) 2021-Present Service Manual: C1f03-72 Stop Lamp Relay

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Adas Control Unit :: Dtc/circuit Diagnosis / C1f03-72 Stop Lamp Relay

Without Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
C1F03 72

OPERATION SW CIRC

(Operation switch circuit) 		Diagnosis condition

  • When engine is running

  • When AEB system is ON
Signal (terminal) —
Threshold Stop lamp inactive state despite the outputting of a stop lamp request signal from ADAS control unit 2
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • BCM

  • ADAS control unit 2

FAIL-SAFE

The following systems are canceled.

  • Vehicle-to-vehicle distance control mode

  • Conventional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • RAB

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C1F03-72” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Turn the AEB system ON

  3. Perform “All DTC Reading”.

  4. Check if the “C1F03-72” is detected as the current malfunction in the “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “C1F03-72” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C1F03-72” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS OF BCM

Check if any DTC is detected in “Self Diagnostic Result” of “BCM”.

Is any DTC detected?

YES>>

Repair or replace the malfunctioning parts identified by the self-diagnosis result. Refer to DTC Index.

NO>>

Replace ADAS control unit 2. Refer to Removal and Installation.

With Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
C1F03 72 OPERATION SW CIRCUIT Diagnosis condition When engine is running
Signal (terminal) Stop lamp request signal
Threshold Stop lamp inactive state despite the outputting of a stop lamp request signal from ADAS control unit 2
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • BCM

  • Chassis control module

  • ADAS control unit 2

FAIL-SAFE

The following systems are canceled.

  • Vehicle speed & vehicle-to-vehicle control function

  • Lane keep function*1

  • Lane keep function*2

  • Lane change support function

  • Overtaking support function

  • Route driving support function

  • FEB

  • RAB

  • PFCW

  • TSR

*1: ProPILOT Assist 2.1 display is green

*2: ProPILOT Assist 2.1 display is blue

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C1F03-72” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE-1

NOTE:

To prevent the possibility of accident, perform component function check instead of DTC confirmation procedure.

  1. Start the engine.

  2. Perform the active test items “STOP LAMP 1” and “STOP LAMP 2” of “BCM” with CONSULT.

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Refer to DTC Diagnosis Procedure.

PERFORM DTC CONFIRMATION PROCEDURE-2

Perform the active test items “Stop lamp ON” of “CHASSIS CONTROL” with CONSULT.

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Refer to DTC Diagnosis Procedure.

DTC Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF BCM

Check if any DTC is detected in “Self Diagnostic Result” of “BCM”.

Is any DTC detected?

YES>>

Repair or replace the malfunctioning parts identified by the self-diagnosis result. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS OF CHASSIS CONTROL MODULE

Check if any DTC is detected in “Self Diagnostic Result” of “CHASSIS CONTROL”.

Is any DTC detected?

YES>>

Repair or replace the malfunctioning parts identified by the self-diagnosis result. Refer to DTC Index.

NO>>

GO TO 3.

CHECK STOP LAMP RELAY POWER SUPPLY CIRCUIT

Check for between stop lamp relay Nissan Ariya vehicle side harness connector and ground.

Stop lamp relay Ground

Voltage

(Approx.)
Connector Terminal
E54 1
3 Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the harnesses or connectors.

CHECK HARNESS BETWEEN STOP LAMP RELAY AND ADAS C/U 2

  1. Turn the ignition switch OFF.

  2. Disconnect chassis control module connector.

  3. Check for continuity between the stop lamp relay Nissan Ariya vehicle side harness connector and the chassis control module vehicle side harness connector.

    Stop lamp relay Chassis control module Continuity
    Connector Terminal Connector Terminal
    E54 4 M32 32 Existed

  4. Check for continuity between chassis control module Nissan Ariya vehicle side harness connector and ground.

    Chassis control module Ground Continuity
    Connector Terminal
    M32 32 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair the harnesses or connectors.

CHECK STOP LAMP RELAY

  1. Disconnect stop lamp relay.

  2. Check stop lamp relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

NO>>

Replace the stop lamp relay.

    C1f03-23 Operation Sw Circ
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F03 23 OPERATION SW CIRC (O...
    C1f03-73 Stop Lamp Relay
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F03 73 OPERATION SW CIRC (O...

    Other materials:

    Action Test
    Ldw Work Procedure Perform action test to verify the customer's concern. Perform action test and check the system operation after system diagnosis. WARNING: Be careful of traffic conditions and safety around the vehicle when performing road test. CAUTION: Fully understand the ...

    Malfunction Area Chart
    Vehicle CAN Communication Circuit MAIN LINE Malfunction area Reference Main line between A/C amp. and air bag diagnosis sensor unit circuit Diagnosis Procedure Main line between active noise control unit and automatic back door control unit circuit Diagnosis Procedure Main line ...

    Basic Inspection. Diagnosis and Repair Work Flow
    Work Flow OVERALL SEQUENCEDETAILED FLOWGET INFORMATION FOR SYMPTOM Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurs). Check operation condition of the function that is malfunctioning. >> G ...