Nissan Rogue (T33) 2021-Present Service Manual: C10ac-54 Calibration Incomplete

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C10ac-54 Calibration Incomplete

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C10AC 54

Calibration incomplete

(Calibration incomplete) 		Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) -
Threshold When calibration of yaw rate/side/decel G sensor is not complete.
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC
Incomplete calibration of G sensor/yaw rate sensor

  • Incomplete calibration of G sensor/yaw rate sensor

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after starting the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C10AC-54” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CALIBRATION OF DECEL G SENSOR

Perform calibration of decel G sensor. Refer to Work Procedure.

>>

GO TO 2.

CALIBRATION OF SIDE G SENSOR

Perform calibration of side G sensor. Refer to Work Procedure.

>>

GO TO 3.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after starting the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C10AC-54” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

    C10aa-63 Pump Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10AA 63 Pump motor (Pump motor) Diagnosis condition When ig...
    C10af-01 Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10AF 01 Pressure sensor (Pressure sensor) Diagnosis conditi...

    Other materials:

    Reporting safety defects
    For USA If you believe that your vehicle has a defect that could cause a crash or lead to injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying NISSAN. This applies whether you drive a Nissan Rogue or another NISSAN model. ...

    Electric Wastegate Control Actuator
    Component Inspection INSPECTION START Do you have CONSULT? Do you have CONSULT? YES>> GO TO 2. NO>> GO TO 3. CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR With CONSULT Turn ignition switch ON and engine stopped. On the CONSULT screen, select “ENGINE”>>“ACTIVE ...

    Door Lock Function
    System Description SYSTEM DIAGRAMDoor lock function controls operation function of the following items. Door lock and unlock function (door request switch) Selective unlock function (door request switch) Reminder function (door request switch) Auto door lock function (door request ...