Nissan Rogue (T33) 2021-Present Service Manual: C10af-01 Pressure Sensor
DTC Description
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |||
|---|---|---|---|---|---|
| C10AF | 01 |
Pressure sensor (Pressure sensor) |
Diagnosis condition |
|
|
| Signal (terminal) | Pressure sensor signal | ||||
| Threshold | When a malfunction is detected in pressure sensor. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
Normal control
DTC CONFIRMATION PROCEDURE
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.
>>
GO TO 2.
CHECK DTC DETECTION
CONSULT
-
Ignition switch OFF (Auto switch OFF).
-
Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
-
Perform self-diagnosis for “ABS”.
Is DTC “C10AF-01” detected?
YES-1>>“CRNT” is displayed: Refer to Diagnosis Procedure.
YES-2>>“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: Inspection End
Diagnosis Procedure
STOP LAMP SWITCH SYSTEM
Check the stop lamp switch system. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace stop lamp switch system.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
CONSULT
-
Erase self-diagnosis result for “ABS”.
-
Ignition switch OFF (Auto ACC function OFF).
-
Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
-
Start the engine and drive the Nissan Ariya vehicle for a short period of time.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
-
Stop the Nissan Ariya vehicle.
-
Perform self-diagnosis for “ABS”.
Is DTC “C10AF-01” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>Check the ABS actuator and electric unit (control unit) harness connector and terminal for damage, looseness and disconnection. Repair / replace harness, connector, or terminal.
Other materials:
C1f00-1c Control Unit
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
C1F00
1C
CONTROL UNIT
(Control unit)
Diagnosis condition
When engine is running
Signal (terminal)
—
Threshold
ADAS control unit 2 internal malfunct ...
B2720-34 Corner Sensor [rl]
DTC Description
DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition
B2720-34
CORNER SENSOR [RL]
(Corner sensor [rear left])
Diagnosis condition
When ignition switch is ON
Signal (terminal)
Rear sonar sensor signal LH outer
Th ...
Driver Monitor Camera Control Unit
Reference Value
VALUES ON THE DIAGNOSIS TOOL Monitor item Condition Value/Status
Left eye
Ignition switch ON
When the open / closed state of the driver's right eye is unclear
Invalid
When the driver's right eye is open
Open
When the driver's right eye is closed
Close
...