Nissan Rogue (T33) 2021-Present Service Manual: C1070-54 Side G Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1070-54 Side G Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1070 54

Side G sensor

(Side G sensor) 		Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) —
Threshold When calibration of side G sensor is not complete.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC
Incomplete calibration of side G sensor

  • Incomplete calibration of side G sensor

  • ABS actuator and electric unit (control unit) install angle is improper
 

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • Brake limited slip differential (BLSD) function

  • Bake assist function

  • Brake force distribution function

  • hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1070-54 detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CALIBRATION OF SIDE G SENSOR

Perform calibration of side G sensor. Refer to Work Procedure.

>>

GO TO 2.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after starting the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1070-54” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

    C1070-01 Side G Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1070 01 Side G sensor (Side G sensor) Diagnosis condition W...
    C1073-01 Vacuum Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1073 01 Vacuum sensor (Vacuum sensor) 1 Diagnosis condition...

    Other materials:

    Plug
    Description Replace the O-ring if oil leaks from the plug. Exploded View 1. Plug 2. O-ring 3. Plug 4. O-ring 5. O-ring 6. Overflow plug 7. O-ring 8. Transaxle assembly     : N·m (kg-m, ft-lb) : N·m (kg-m, in-lb) : Always replace ...

    Oil Level Sensor Signal Circuit
    DiagnosisProcedure CHECK OIL LEVEL SENSOR CIRCUIT Ignition switch OFF. Disconnect combination meter harness connector and oil level sensor harness connector. Check continuity between combination meter harness connector and oil level sensor harness connector. Combination meter Oi ...

    Removal and Installation. Front Fender
    Exploded View Fender cover Front fender ledge cover Front fender bracket Front fender assembly Front fender baffle     : Pawl : N·m (kg-m, in-lb) Front Fender Removal and Installation REMOVALRemove front fender protector. Refer to Removal an ...