Nissan Rogue (T33) 2021-Present Service Manual: C1070-01 Side G Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1070-01 Side G Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1070 01

Side G sensor

(Side G sensor) 		Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) Side G sensor signal
Threshold When a malfunction is detected in side G sensor signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Change in Nissan Ariya vehicle posture (e.g. different tire sizes on front and rear, overloaded)

  • ABS actuator and electric unit (control unit) install angle is improper

  • Harness or connector

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Change in Nissan Ariya vehicle posture (e.g. different tire sizes on front and rear, overloaded)

  • ABS actuator and electric unit (control unit) install angle is improper

  • Harness or connector

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery
 

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • Brake limited slip differential (BLSD) function

  • Bake assist function

  • Brake force distribution function

  • hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1070-01” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK SELF-DIAGNOSIS RESULTS

CONSULT

Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1070-01” in self-diagnosis for “ABS”.

>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

    C106e-55 Steering Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C106E 55 Steering angle sensor (Steering angle sensor) Diagn...
    C1070-54 Side G Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1070 54 Side G sensor (Side G sensor) Diagnosis condition W...

    Other materials:

    Propilot Assist 2.1. Symptom Diagnosis. Propilot Assist 2.1
    Propilot Assist 2.1 Propilot Assist 2.0 System Symptoms Symptom Table Check whether symptom is due to normal operation before performing diagnosis. Refer to Precautions for ProPILOT Assist 2.1. Symptoms Reference page ProPILOT Assist 2.1 cannot be turned ON Diagnosis Procedure Nissa ...

    Dtc/circuit Diagnosis. B2428-52 Automatic Back Door Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2428-52 Automatic back door control unit (Automatic back door control unit) Diagnosis condition All times Signal (terminal) — Threshold Automatic ...

    Symptom Diagnosis. Automatic Back Door Functions Do Not Cancel
    Diagnosis Procedure CHECK “POWER BACK DOOR SETTING” IN COMBINATION METER Check “Power back door setting” is in the OFF. Is the inspection result normal? YES>> GO TO 2. NO>> Set “Power back door setting” to “OFF”. REPLACE AUTOMATIC BACK DOOR CONTROL UNIT Rep ...