Nissan Rogue (T33) 2021-Present Service Manual: C1067-11 Rr Rh Wheel Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1067-11 Rr Rh Wheel Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1067 11

RR RH wheel sensor

(Rear right wheel sensor) 		Diagnosis condition

  • When ignition switch is ON.

  • When rear right wheel sensor power supply voltage is normal.
Signal (terminal)

  • Rear right wheel sensor signal

  • Rear right wheel sensor power supply
Threshold When an short circuit is detected in rear right wheel sensor circuit.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Nissan Ariya Vehicle was not driven after previous repair

  • Harness or connector

  • Rear right wheel sensor

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • ABS function

  • EBD function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  2. Perform self-diagnosis for “ABS”.

Is DTC “C1067-11” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CAUTION:

Never check between wheel sensor harness connector terminals.

CHECK WHEEL SENSOR

  1. Disconnect 12V battery negative terminal.

  2. Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 3 .

NO>>

GO TO 2 .

REPLACE WHEEL SENSOR (1)

CONSULT

  1. Replace the rear right wheel sensor. Refer to Removal and Installation.

  2. Connect 12V battery negative terminal.

  3. Erase self-diagnosis result for “ABS”.

  4. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  5. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C1067-11” detected?

YES>>

GO TO 3 .

NO>>

Inspection End

CHECK CONNECTOR

  1. Disconnect 12V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

  3. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 5 .

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 4 .

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Connect 12V battery negative terminal.

  2. Erase self-diagnosis result for “ABS”.

  3. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  4. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  5. Perform self-diagnosis for “ABS”.

Is DTC “C1067-11” detected?

YES>>

GO TO 5 .

NO>>

Inspection End

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6 .

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector and then check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

  3. Disconnect rear right wheel sensor harness connector and check the rear right wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 8 .

NO>>

Repair / replace harness, connector, or terminal. GO TO 7 .

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC “C1067-11” detected?

YES>>

GO TO 8 .

NO>>

Inspection End

CHECK WHEEL SENSOR HARNESS

  1. Disconnect 12V battery negative terminal.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and rear right wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity
      Connector Terminal Connector Terminal
      E125 22 B67 1 Existed

    • Measurement connector and terminal for signal circuit

      ABS actuator and electric unit (control unit) Rear right wheel sensor Continuity
      Connector Terminal Connector Terminal
      E125 37 B67 2 Existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 9 .

PERFORM SELF-DIAGNOSIS (3)

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC “C1067-11” detected?

YES>>

GO TO 10.

NO>>

Inspection End

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: NI-45741) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

    NOTE:

    The green POWER indicator should illuminate. If the POWER indicator does not illuminate, replace the battery in the ABS active wheel sensor tester before proceeding.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

    NOTE:

    If the red SENSOR indicator illuminates but does not flash, reverse the polarity of the tester leads and retest.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

GO TO 11.

REPLACE WHEEL SENSOR

CONSULT

  1. Replace the rear right wheel sensor. Refer to Removal and Installation.

  2. Connect ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC “C1067-11” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

    C1067-09 Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1067 09 RR RH wheel sensor (Rear right wheel sensor) Diagno...
    C1067-12 Rr Rh Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1067 12 RR RH wheel sensor (Rear right wheel sensor) Diagno...

    Other materials:

    Dtc/circuit Diagnosis. Thigh Support Motor
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Thigh support motor” in “Active test” mode of “DRIVER SEAT”. Check thigh support motor LH operation. Test item Operation Thigh support motor Up Thigh support Upward Down ...

    Automatic air conditioner (models without rear control)
    Models with heated steering wheel Models without heated steering wheel Basic information Temperature control dial (driver's side) AUTO button Display screen SYNC button Temperature control dial (passenger's side) ON·OFF button Air recirculation button Fan speed buttons Air flow ...

    P02cd Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02CD 00 CYL1 INJECTOR OFFSET LEARNING (Cylinder 1 Fuel Injector "A" Offset Learning At Max Limit) Diagnosis condition Engine running During injector ...