Nissan Rogue (T33) 2021-Present Service Manual: C0552 G Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / C0552 G Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C0552 00

Longitudinal Acceleration Sensor Range/Performance

(Longitudinal Acceleration Sensor Range/Performance) 		Diagnosis condition

  • Ignition switch ON

  • Battery voltage: 11 V
Signal CAN communication signal
Threshold When some DTC is detected in the VDC and via CAN communication is sent to the ECM
Diagnosis delay time 12 seconds or more

POSSIBLE CAUSE

  • G sensor

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

Not applicable

DTC Confirmation Procedure

CHECK DTC

Perform the confirmation procedure for displayed DTC with VDC. Refer to below:

  • DTC C1058-42: Refer to DTC Description.

  • DTC C1058-44: Refer to DTC Description.

  • DTC C1058-51: Refer to DTC Description.

  • DTC C1070-01: Refer to DTC Description.

  • DTC C1070-54: Refer to DTC Description.

  • DTC C1070-64: Refer to DTC Description.

  • DTC C1071-01: Refer to DTC Index.

  • DTC C1071-64: Refer to DTC Description.

  • DTC C1072-01: Refer to DTC Description.

  • DTC C1072-64: Refer to DTC Description.

  • DTC C107A-55: Refer to DTC Description .

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC

Perform the confirmation procedure for displayed DTC with VDC. Refer to below:

  • DTC C1058-42: Refer to Diagnosis Procedure.

  • DTC C1058-44: Refer to Diagnosis Procedure.

  • DTC C1058-51: Refer to Diagnosis Procedure.

  • DTC C1070-01: Refer to Diagnosis Procedure.

  • DTC C1070-54: Refer to Diagnosis Procedure.

  • DTC C1070-64: Refer to Diagnosis Procedure.

  • DTC C1071-01: Refer to DTC Index.

  • DTC C1071-64: Refer to Diagnosis Procedure.

  • DTC C1072-01: Refer to Diagnosis Procedure.

  • DTC C1072-64: Refer to Diagnosis Procedure.

  • DTC C107A-55: Refer to Diagnosis Procedure.

Is inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

    C053c Wheel Speed Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C053C 00 Wheel speed sensor (Wheel speed sensor generic range/pe...
    P0010 Intake Valve Timing Control
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0010 00 A camshaft position actuator B1 (“A” camshaft posit...

    Other materials:

    Dtc/circuit Diagnosis. Horn Function
    Component Function Check CHECK FUNCTION CONSULT Ignition switch OFF. Perform “Horn” in “Active test” mode of “IPDM E/R”. Check the horn operation. Test item Description Horn On Horn Sounds (for 20 ms.) Is the operation normal? YES>> Ins ...

    Engine Stand Setting
    Setting NOTE: Explained here is how to disassemble with engine stand supporting transaxle surface. When using different type of engine stand, note with difference in steps and etc. Remove the engine and the transaxle assembly from the vehicle, and separate the transaxle from the engine. Ref ...

    System Description. Diagnosis System (occupant Detection System Control Unit)
    CONSULT Function APPLICATION ITEMCONSULT performs the following functions. Diagnosis mode CGW Status Description Restricted Mode Diag Test Mode Open Mode CGW Information Display Display Display Display the current CGW mode Enables CGW to switch mode Data mo ...