Nissan Rogue (T33) 2021-Present Service Manual: P0010 Intake Valve Timing Control

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0010 Intake Valve Timing Control

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0010 00

A camshaft position actuator B1

(“A” camshaft position actuator control circuit/open bank 1) 		Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold The electric intake valve timing control module detects internal power stage malfunction
Diagnosis delay time —

POSSIBLE CAUSE

  • Electric intake valve timing (IVT) control module

  • Electric intake valve timing (IVT) control module power supply

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.

or

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ELECTRIC INTAKE VALVE TIMING (IVT) CONTROL MODULE POWER SUPPLY AND GROUND CIRCUIT

Check electric IVT control module power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Erase DTC.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is the DTC P0010 detected again?

YES>>

Replace electric IVT control module. Refer to ELECTRIC INTAKE VALVE TIMING CONTROL MODULE : Removal & Installation.

NO>>

INSPECTION END

    C053c Wheel Speed Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C053C 00 Wheel speed sensor (Wheel speed sensor generic range/pe...
    P0011 Ivt Control
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0011 00 INT/V TIM CONT-B1 (“A” Camshaft position - timing o...

    Other materials:

    U0079-00 Can Comm Circuit
    DTC Description DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real-time application. It is an onNissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equippe ...

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...

    System Description. Component Parts. Srs Air Bag Control System
    Srs Air Bag Control System Component Parts Location 1. Rear side air bag module 2. Curtain air bag module 3. Front side air bag module 4. Knee air bag module 5. Passenger air bag module 6. Front seat belt buckle switch 7. BCM (Body Control Module) Refe ...