Nissan Rogue (T33) 2021-Present Service Manual: C0505 Wheel Speed Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / C0505 Wheel Speed Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C0505 00

Left front wheel speed sensor

(Left Front Wheel Speed Sensor Correlation) 		Diagnosis condition

  • Ignition switch ON

  • Battery voltage: 11 V
Signal CAN communication signal
Threshold When some DTC is detected in the VDC and via CAN communication is sent to the ECM
Diagnosis delay time 12 seconds or more

POSSIBLE CAUSE

  • Wheel speed sensor FL

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

Not applicable

DTC Confirmation Procedure

CHECK DTC

Perform the confirmation procedure for displayed DTC with VDC. Refer to below:

  • DTC C1061-02: Refer to DTC Description.

  • DTC C1061-07: Refer to DTC Description.

  • DTC C1061-13: Refer to DTC Description.

  • DTC C1061-38: Refer to DTC Description.

  • DTC C1061-4A: Refer to DTC Description.

  • DTC C1061-64: Refer to DTC Description.

  • DTC C1068-95: Refer to DTC Description.

  • DTC C106A-55: Refer to DTC Description.

  • DTC C106A-62: Refer to DTC Description.

  • DTC C106A-64: Refer to DTC Description.

  • DTC C106A-95: Refer to DTC Index.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC

Perform the confirmation procedure for displayed DTC with VDC. Refer to below:

  • DTC C1061-02: Refer to Diagnosis Procedure.

  • DTC C1061-07: Refer to Diagnosis Procedure.

  • DTC C1061-13: Refer to Diagnosis Procedure.

  • DTC C1061-38: Refer to Diagnosis Procedure.

  • DTC C1061-4A: Refer to Diagnosis Procedure.

  • DTC C1061-64: Refer to Diagnosis Procedure.

  • DTC C1068-95: Refer to Diagnosis Procedure.

  • DTC C106A-55: Refer to Diagnosis Procedure.

  • DTC C106A-62: Refer to Diagnosis Procedure.

  • DTC C106A-64: Refer to Diagnosis Procedure.

  • DTC C106A-95: Refer to DTC Index.

Is inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

    C0069 G Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C0069 00 Yaw Rate/Longitude Sensors (Yaw Rate/Longitude Sensors)...
    C053c Wheel Speed Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C053C 00 Wheel speed sensor (Wheel speed sensor generic range/pe...

    Other materials:

    Rear Final Drive: R145. Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
    Noise, Vibration and Harshness (nvh) Troubleshooting NVH Troubleshooting Chart Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts. Possible cause and SUSPECTED PARTS Symptom Reference Noise Vibration Gear tooth rough × – Inspectio ...

    Kr15ddt. Precaution
    Precaution for Procedure without Cowl Top Cover When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc to prevent damage to windshield. Precautions for Removing Battery Terminal With the adoption of Auto ACC function, ACC power is ...

    Basic Inspection. Intelligent Key Interlock Storing
    Description Always perform the Intelligent Key interlock function storage when the driver seat control unit is replaced. The Intelligent Key interlock function will not operate normally if no memory storage is performed. For details, refer to Work Procedure. Work Procedure Intelligent Key I ...