Nissan Rogue (T33) 2021-Present Service Manual: B24f7-93 Air Mix Door Motor 1

Nissan Rogue (T33) 2021-Present Service Manual / Ventilation, Heater & Air Conditioner :: Heater & Air Conditioning Control System / Automatic Air Conditioning :: Dtc/circuit Diagnosis / B24f7-93 Air Mix Door Motor 1

DTC Description

DTC DETECTION LOGIC

NOTE:

If all of door motors DTC (B2480-93*, B24F5-93, B24F6-93, B24F7-93, B24F8-93) are detected, check “DOOR MOTOR”. Refer to Diagnosis Procedure.

*: With rear air control

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
B24F7-93

Air mix door motor 1

(Air mix door motor 1) 		Diagnosis condition Ignition switch ON
Signal (Terminal) LIN (door motor) signal
Threshold Drive error of air mix door motor LH is detected
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Harness and connector (air mix door motor LH circuit is open or shorted to ground)

  • Air mix door motor LH installation condition

  • Air mix door motor LH

  • A/C amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Start the engine.

  2. Select “Self diagnosis result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK AIR MIX DOOR MOTOR LH POWER SUPPLY

  1. Ignition switch ON.

  2. Check voltage between air mix door motor LH harness connector and A/C amp. harness connector.

(+) (−) Voltage
Air mix door motor LH A/C amp.
Connector Terminal Connector Terminal
M145 1 M55 58 Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK AIR MIX DOOR MOTOR LH GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor LH connector and A/C amp. connector.

  3. Check continuity between air mix door motor LH harness connector and A/C amp. harness connector.

    Air mix door motor LH A/C amp. Continuity
    Connector Terminal Connector Terminal
    M145 2 M54 27 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR LH LIN SIGNAL CIRCUIT

  1. Connect air mix door motor LH connector and A/C amp. connector.

  2. Ignition switch ON.

  3. Confirm output waveform between air mix door motor LH harness connector and A/C amp. harness connector with oscilloscope.

    (+) (−) Output waveform
    Air mix door motor LH A/C amp.
    Connector Terminal Connector Terminal
    M145 3 M55 58

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 6.

CHECK INSTALLATION OF AIR MIX DOOR MOTOR LH

Check air mix door motor LH is properly installed. Refer to Exploded View.

Is the inspection result normal?

YES>>

Replace air mix door motor LH. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning part.

CHECK AIR MIX DOOR MOTOR LH POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor LH connector and A/C amp. connector.

  3. Check continuity between air mix door motor LH harness connector and A/C amp. harness connector.

    Air mix door motor LH A/C amp. Continuity
    Connector Terminal Connector Terminal
    M145 1 M54 1 Yes

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR LH LIN SIGNAL CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor LH connector and A/C amp. connector.

  3. Check continuity between air mix door motor LH harness connector and A/C amp. harness connector.

    Air mix door motor LH A/C amp. Continuity
    Connector Terminal Connector Terminal
    M145 3 M54 2 Yes

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

    B24f6-93 Intake Door Motor
    DTC Description DTC DETECTION LOGICNOTE: If all of door motors DTC (B2480-93*, B24F5-93, B24F6-93, B24F7-93, B24F8-93) are detected, check “DOOR MOTOR”. Refer to Diagnosis P...
    B24f8-93 Air Mix Door Motor 2
    DTC Description DTC DETECTION LOGICNOTE: If all of door motors DTC (B2480-93*, B24F5-93, B24F6-93, B24F7-93, B24F8-93) are detected, check “DOOR MOTOR”. Refer to Diagnosis P...

    Other materials:

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...

    C1203-86 Abs Signal
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1203-86 ABS SYSTEM (Antilock brake system) Diagnosis condition Ignition switch: ON Nissan Ariya Vehicle running Signal Wheel speed signals ...

    Power Supply and Ground Circuit
    8ch Can Gateway Diagnosis Procedure CHECK FUSE Check that the following fuse are not blown. Signal name Fuse No. Battery power supply 16 Ignition power supply 9 Is the fuse blown (open)? YES>> Replace the blown fuse after repairing the affected circuit if a fuse ...