Nissan Rogue (T33) 2021-Present Service Manual: B24f8-93 Air Mix Door Motor 2

Nissan Rogue (T33) 2021-Present Service Manual / Ventilation, Heater & Air Conditioner :: Heater & Air Conditioning Control System / Automatic Air Conditioning :: Dtc/circuit Diagnosis / B24f8-93 Air Mix Door Motor 2

DTC Description

DTC DETECTION LOGIC

NOTE:

If all of door motors DTC (B2480-93*, B24F5-93, B24F6-93, B24F7-93, B24F8-93) are detected, check “DOOR MOTOR”. Refer to Diagnosis Procedure.

*: With rear air control

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
B24F8-93

Air mix door motor 2

(Air mix door motor 2) 		Diagnosis condition Ignition switch ON
Signal (Terminal) LIN (door motor) signal
Threshold Drive error of air mix door motor RH is detected
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Harness and connector (air mix door motor RH circuit is open or shorted to ground)

  • Air mix door motor RH installation condition

  • Air mix door motor RH

  • A/C amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Start the engine.

  2. Select “Self diagnosis result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK AIR MIX DOOR MOTOR RH POWER SUPPLY

  1. Ignition switch ON.

  2. Check voltage between air mix door motor RH harness connector and A/C amp. harness connector.

(+) (−) Voltage
Air mix door motor RH A/C amp.
Connector Terminal Connector Terminal
M140 1 M55 58 Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK AIR MIX DOOR MOTOR RH GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor RH connector and A/C amp. connector.

  3. Check continuity between air mix door motor RH harness connector and A/C amp. harness connector.

    Air mix door motor RH A/C amp. Continuity
    Connector Terminal Connector Terminal
    M140 2 M54 27 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR RH LIN SIGNAL CIRCUIT

  1. Connect air mix door motor RH connector and A/C amp. connector.

  2. Ignition switch ON.

  3. Confirm output waveform between air mix door motor RH harness connector and A/C amp. harness connector with oscilloscope.

    (+) (−) Output waveform
    Air mix door motor RH A/C amp.
    Connector Terminal Connector Terminal
    M140 3 M55 58

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 6.

CHECK INSTALLATION OF AIR MIX DOOR MOTOR RH

Check air mix door motor RH is properly installed. Refer to Exploded View.

Is the inspection result normal?

YES>>

Replace air mix door motor RH. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning part.

CHECK AIR MIX DOOR MOTOR RH POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor RH connector and A/C amp. connector.

  3. Check continuity between air mix door motor RH harness connector and A/C amp. harness connector.

    Air mix door motor RH A/C amp. Continuity
    Connector Terminal Connector Terminal
    M140 1 M54 1 Yes

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR RH LIN SIGNAL CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor RH connector and A/C amp. connector.

  3. Check continuity between air mix door motor RH harness connector and A/C amp. harness connector.

    Air mix door motor RH A/C amp. Continuity
    Connector Terminal Connector Terminal
    M140 3 M54 2 Yes

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

    B24f7-93 Air Mix Door Motor 1
    DTC Description DTC DETECTION LOGICNOTE: If all of door motors DTC (B2480-93*, B24F5-93, B24F6-93, B24F7-93, B24F8-93) are detected, check “DOOR MOTOR”. Refer to Diagnosis P...
    U1ca1-08 Lin Communication 2
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CA1-08 LIN communication 2 (Local interconnect network com...

    Other materials:

    Dtc/circuit Diagnosis. C18de-82 Brake Power Supply Back up Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18DE 82 Backup power supply unit communication Diagnosis condition When Ignition switch is ON. Signal (terminal) Brake power supply backup unit signal Threshold When a malfunct ...

    B2730-13 Side Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2730-13 SIDE SENSOR [RL] (Side sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH side Threshold H ...

    Dtc/circuit Diagnosis. P161d-00 Immobilizer
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition P161D-00 IMMOBILIZER (Immobilizer) Diagnosis condition Ignition switch ON Signal (terminal) — Threshold When Intelligent Key unit detects an immob ...