Nissan Rogue (T33) 2021-Present Service Manual: Automatic Air Conditioning :: Symptom Diagnosis

Nissan Rogue (T33) 2021-Present Service Manual / Ventilation, Heater & Air Conditioner :: Heater & Air Conditioning Control System / Automatic Air Conditioning :: Symptom Diagnosis

Automatic Air Conditioner System

Symptom Table

NOTE:

Perform "Self diagnosis result" with CONSULT before performing the symptom diagnosis. If any DTC is detected, perform the corresponding diagnosis.

Symptom Corresponding malfunction part Check item/Reference

Air conditioning system does not activate.

NOTE:

Fail-safe does not activate.

  • Fuse

  • A/C amp. power supply or ground circuit

  • A/C amp.

Check A/C amp. power supply and ground circuits.

Refer to Diagnosis Procedure.
Air conditioning cannot be controlled. All control

  • Fuse

  • A/C switch assembly power supply or ground circuit

  • A/C amp.

Check A/C switch assembly power supply and ground circuits.

Refer to Diagnosis Procedure.
A part of control A/C switch assembly

Replace A/C switch assembly.

Refer to Removal and Installation.
A/C switch assembly display or switch indicator lamp does not display correctly.

The results of A/C switch assembly on board diagnosis are normal.

Refer to Diagnosis Description.
Discharge air temperature (driver side) does not change. Air mix door motor (driver side) system installation condition

Check air mix door motor (driver side) system is properly installed.

Refer to Exploded View.
Discharge air temperature (passenger side) does not change. Air mix door motor (passenger side) system installation condition

Check air mix door motor (passenger side) system is properly installed.

Refer to Exploded View.
Discharge air temperature (rear side) does not change. Air mix door motor (rear side) system installation condition

Check air mix door motor (rear side) system is properly installed.

Refer to Exploded View.
Air outlet does not change. Mode door motor system installation condition

Check mode door motor system is properly installed.

Refer to Exploded View.
Air inlet does not change. Intake door motor system installation condition

Check intake door motor system is properly installed.

Refer to Exploded View.
Front blower motor does not operates or operation speed is not normal.

  • Fuse

  • Front blower motor

  • Front blower motor power supply or ground circuit

  • Front blower motor control signal circuits

  • A/C amp.

Check front blower motor circuits.

Refer to Diagnosis Procedure.
A/C compressor does not operate.

  • Magnetic clutch

  • Magnetic clutch power supply or ground circuit

  • IPDM E/R (Smart FET)

  • The circuit between ECM and refrigerant pressure sensor

  • Refrigerant pressure sensor

  • ECM

  • A/C amp.

 Refer to Diagnosis Procedure.

  • Insufficient cooling

  • No cool air comes out. (Air flow volume is normal.)

  • Magnetic clutch control system

  • Drive belt slipping

  • Cooler cycle

  • ECV (Electrical control valve)

  • Air leakage from each duct

  • Sunload sensor

  • Temperature setting trimmer

 Refer to Diagnosis Procedure.

  • Insufficient heating

  • No warm air comes out. (Air flow volume is normal.)

  • Engine cooling system

  • Heater hose

  • Heater core

  • Air leakage from each duct

  • PTC heater system

  • Sunload sensor

  • Temperature setting trimmer

 Refer to Diagnosis Procedure.
Noise is heard when the air conditioning operates. During A/C compressor operation Cooler cycle

Symptom table for noise

Refer to Symptom Table.
During front blower motor operation

  • Mixing any foreign object in front blower motor

  • Front blower motor fan breakage

  • Front blower motor rotation inferiority

Check front blower motor.

Refer to Component Inspection (Front Blower Motor).

Insufficient Cooling

Description

Symptom

  • Insufficient cooling

  • No cool air comes out. (Air flow volume is normal.)

Diagnosis Procedure

NOTE:

Perform "Self diagnosis result" with CONSULT before performing symptom diagnosis. If any DTC is detected, perform the corresponding diagnosis.

CHECK MAGNETIC CLUTCH OPERATION

  1. Ignition switch ON.

  2. Push fan switch and operate blower fan.

  3. Press A/C switch.

  4. Check that A/C indicator turns ON. Check visually and by sound that A/C compressor operates.

  5. Press A/C switch again.

  6. Check that A/C indicator turns OFF. Check that A/C compressor stops.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform diagnosis of “A/C COMPRESSOR DOES NOT OPERATE” in “SYMPTOM DIAGNOSIS”. Refer to Diagnosis Procedure.

CHECK DRIVE BELT

Check tension of drive belt. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Adjust or replace drive belt depending on the inspection results.

CHECK REFRIGERANT CYCLE PRESSURE

Connect recovery/recycling recharging equipment to the Nissan Ariya vehicle and perform pressure inspection with gauge. Refer to Symptom Table.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace parts depending on the inspection results.

CHECK ECV

Perform ECV circuit diagnosis. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace parts depending on the inspection results.

CHECK AIR LEAKAGE FROM EACH DUCT

Check duct and nozzle, etc. of the air conditioning system for leakage.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace parts depending on the inspection results.

CHECK SUNLOAD SENSOR

Perform sunload sensor diagnosis. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace parts depending on the inspection results.

CHECK SETTING OF TEMPERATURE SETTING TRIMMER

  1. Check setting value of temperature setting trimmer. Refer to CONSULT Function.

  2. Check that temperature setting trimmer is set to “+ direction”.

    NOTE:

    The control temperature can be set with the setting of the temperature setting trimmer.

  3. Set difference between the set temperature and control temperature to “0”.

Is inspection result normal?

YES>>

Inspection End.

NO>>

Replace A/C amp. Refer to Removal and Installation.

Insufficient Heating

Description

Symptom

  • Insufficient heating

  • No warm air comes out. (Air flow volume is normal.)

Diagnosis Procedure

NOTE:

Perform "Self diagnosis result" with CONSULT before performing symptom diagnosis. If any DTC is detected, perform the corresponding diagnosis.

CHECK COOLING SYSTEM

  1. Check engine coolant level and check for leakage. Refer to Inspection.

  2. Check reservoir tank cap. Refer to Inspection.

  3. Check water flow sounds of the engine coolant. Refer to Refilling.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Refill engine coolant and repair or replace the parts depending on the inspection results.

CHECK HEATER HOSE

Check installation of heater hose by visually or touching.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace parts depending on the inspection results.

CHECK HEATER CORE

  1. Check temperature of inlet hose and outlet hose of heater core.

  2. Check that inlet side of heater core is hot and the outlet side is slightly lower than/almost equal to the inlet side.

    CAUTION:

    Always perform the temperature inspection in a short period of time because the engine coolant temperature is very hot.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace heater core. Refer to Removal and Installation.

CHECK AIR LEAKAGE FROM EACH DUCT

Check duct and nozzle, etc. of the air conditioning system for air leakage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace parts depending on the inspection results.

CHECK PTC HEATER

Perform PTC heater diagnosis. Refer to Component Function Check.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace parts depending on the inspection results.

CHECK SUNLOAD SENSOR

Perform sunload sensor diagnosis. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace parts depending on the inspection results.

CHECK SETTING OF TEMPERATURE SETTING TRIMMER

  1. Check setting value of temperature setting trimmer. Refer to CONSULT Function.

  2. Check that temperature setting trimmer is set to “− direction”.

    NOTE:

    The control temperature can be set by the temperature setting trimmer.

  3. Set difference between the set temperature and control temperature to “0”.

Are the symptoms solved?

YES>>

Inspection End.

NO>>

Replace A/C amp. Refer to Removal and Installation.

A/c Compressor Does Not Operate

Description

SYMPTOM

A/C compressor does not operate.

Diagnosis Procedure

NOTE:

  • Perform "Self diagnosis result" with CONSULT before performing symptom diagnosis. If any DTC is detected, perform the corresponding diagnosis.

  • Check that refrigerant is enclosed in cooler cycle normally. If refrigerant amount is shortage from proper amount, perform the inspection of refrigerant leakage.

CHECK MAGNETIC CLUTCH OPERATION

Check magnetic clutch. Refer to Component Function Check.

Does it operate normally?

YES>>

GO TO 2.

NO>>

Repair or replace malfunctioning parts.

CHECK REFRIGERANT PRESSURE SENSOR

Check refrigerant pressure sensor. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace malfunctioning parts.

CHECK A/C AMP. OUTPUT SIGNAL

CONSULT

  1. Select “Data monitor” mode of “HVAC”.

  2. Select “Compressor request signal” and “FAN REQ SIG”, and check status under the following conditions.

Monitor item Condition Status
Compressor request signal A/C switch OFF (A/C switch indicator: OFF) Off
ON (A/C switch indicator: ON) On
FAN REQ SIG Front blower motor OFF Off
ON On

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Replace A/C amp. Refer to Removal and Installation.

    Ptc Heater
    Component Function Check CHECK PTC HEATER OPERATION Start the engine. Operate front blower motor. Operate temperature control dial to full hot position. Check for warm air at di...
    Automatic Air Conditioning. Removal and Installation
    A/c Switch Assembly Exploded View A/C switch assembly Center ventilator finisher     : Pawl : Nissan Ariya Vehicle front Removal and Installation REMOVALRemove center ...

    Other materials:

    It Can Communication Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...

    P14a7 Charge Air Cooler Cooling Electric Water Pump
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P14A7 Charge air cooler cooling electric W/P (Charge air cooler cooling electric water pump) Diagnosis condition Engine running at idle Warm-up conditio ...