Nissan Rogue (T33) 2021-Present Service Manual: Ambient Sensor Signal Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Meter, Warning Lamp & Indicator / Type a :: Dtc/circuit Diagnosis / Ambient Sensor Signal Circuit

Diagnosis Procedure

CHECK AMBIENT SENSOR POWER SUPPLY

  1. Ignition switch OFF.

  2. Disconnect ambient sensor harness connector.

  3. Ignition switch ON.

  4. Check voltage between ambient sensor harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Ambient sensor
    Connector Terminal
    E76 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK AMBIENT SENSOR GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between ambient sensor harness connector and ground.

    Ambient sensor — Continuity
    Connector Terminal
    E76 1 Ground Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connector.

CHECK AMBIENT SENSOR

Check ambient sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Replace ambient sensor. Refer to Removal and Installation.

CHECK AMBIENT SENSOR POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect combination meter harness connector.

  3. Check continuity between ambient sensor harness connector and combination meter harness connector.

    Ambient sensor Combination meter Continuity
    Connector Terminal Connector Terminal
    E76 1

    M73 (U.S.A. production)

    M77 (Japan production)     		29 Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness or connector.

CHECK AMBIENT SENSOR POWER SUPPLY CIRCUIT FOR GROUND SHORT

Check continuity between ambient sensor harness connector and ground.

Ambient sensor — Continuity
Connector Terminal
E76 2 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness or connector.

CHECK AMBIENT SENSOR POWER SUPPLY CIRCUIT FOR POWER SHORT

  1. Ignition switch ON.

  2. Check voltage between ambient sensor harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Ambient sensor
    Connector Terminal
    E76 1 Ground 0 V

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace harness or connector.

Component Inspection

CHECK AMBIENT SENSOR

  1. Remove ambient sensor. Refer to Removal and Installation.

  2. Check resistance between ambient sensor terminals.

    Terminal Condition Resistance: kΩ
    Temperature: °C (°F)
    1 2 −20 (−4) 16.50
    −10 (14) 9.92
    0 (32) 6.19
    10 (50) 3.99
    20 (68) 2.65
    25 (77) 2.19
    30 (86) 1.81
    40 (104) 1.27

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace ambient sensor. Refer to Removal and Installation.

    Fuel Level Sensor Signal Circuit
    Component Function Check PERFORM COMPONENT FUNCTION CHECK (1) Ignition switch OFF. Disconnect fuel level sensor unit, fuel pump and FPCM (fuel level sensor) (main) harness conne...
    Oil Level Sensor Signal Circuit
    DiagnosisProcedure CHECK OIL LEVEL SENSOR CIRCUIT Ignition switch OFF. Disconnect combination meter harness connector and oil level sensor harness connector. Check continuity be...

    Other materials:

    Adas Control Unit. Basic Inspection
    Additional Service When Replacing Adas Control Unit 2 Without Propilot Assist 2.1 Work Procedure Always perform the additional service after replacing the ADAS control unit 2.ADAS CONTROL UNIT 2 CONFIGURATION Perform saving Nissan Ariya vehicle internal information according to "Replace ECU" i ...

    U2212 Can Comm Err (brake Unit)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms DTC detection condition U2212 87 CAN communication error brake unit Diagnosis condition Ignition switch ON Signal (terminal) CAN communication signal Threshold ECM is not recieving CAN communication ...

    Preparation
    Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description KV10115801 (NI-38956) Oil filter wrench Removing and installing oil filter a: 64.3 mm (2.531 in) KV311039S0 ( — ) Chargin ...