Nissan Rogue (T33) 2021-Present Service Manual: Wireless Charger :: Dtc/circuit Diagnosis

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Power Outlet / Wireless Charger :: Dtc/circuit Diagnosis

B1b00-08 Can Communication

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
B1B00-08

CAN COMMUNICATION

(CAN COMMUNICATION) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission error or reception error
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "B1B00‐08" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. DTC confirmation procedure again. Refer to DTC Description.

Is DTC "B1B00‐08" detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

B1b01-1c Wireless Charger Unit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
B1B01-1C

Wireless charger unit

(Wireless charger unit) 		Diagnosis condition When ignition switch is ON
Signal (terminal)

Ignition power supply voltage

(terminal#1)
Threshold More than 18.5 V
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Ignition power supply is high voltage

  • Wireless charger unit malfunction

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "B1B01‐1C" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK WIRELESS CHARGER UNIT POWER SUPPLY CIRCUIT

Check wireless charger unit power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace wireless charger unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B1b02-1d Wireless Charger Unit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
B1B02-1D

Wireless charger unit

(Wireless charger unit) 		Diagnosis condition When ignition switch is ON
Signal (terminal)

Ignition power supply voltage

(terminal#1)
Threshold When the input power calculated internally is 35 W or more
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Ignition power supply circuit malfunction.

  • Wireless charger unit malfunction

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "B1B02‐1D" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK WIRELESS CHARGER UNIT POWER SUPPLY CIRCUIT

Check wireless charger unit power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace wireless charger unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B1b03-49 Wireless Charger Unit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
B1B03-49

Wireless charger unit

(Wireless charger unit) 		1 Diagnosis condition When ignition switch is ON
Signal (terminal) -
Threshold Internal malfunction
Diagnosis delay time 1 second or more
2 Diagnosis condition When ignition switch is ON
Signal (terminal) -
Threshold Internal malfunction
Diagnosis delay time 3.2 seconds or more

POSSIBLE CAUSE

Wireless charger unit malfunction.

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "B1B03‐49" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "B1B03-49" detected again?

YES>>

Replace wireless charger unit. Refer to Removal and Installation.

NO>>

Inspection End.

B1b05-09 Wireless Charger Unit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
B1B05-09

Wireless charger unit

(Wireless charger unit) 		1 Diagnosis condition When ignition switch is ON
Signal (terminal) Wireless charger indicator signal
Threshold Green and Yellow LED is not controlled
Diagnosis delay time At system startup
2 Diagnosis condition When ignition switch is ON
Signal (terminal) Wireless charger indicator signal
Threshold Green and Yellow LED is not controlled
Diagnosis delay time At system startup

POSSIBLE CAUSE

  • Wireless charger indicator circuit open or short

  • Wireless charger indicator malfunction

  • Wireless charger unit malfunction.

FAIL-SAFE

-

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "B1B05‐09" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK HARNESS BETWEEN WIRELESS CHARGER UNIT AND WIRELESS CHARGER INDICATOR

CONSULT

  1. Ignition switch OFF.

  2. Disconnect the wireless charger unit and wireless charger indicator connector.

  3. Check for continuity between the wireless charger unit harness connector and wireless charger indicator harness connector.

    Wireless charger unit Wireless charger indicator Continuity
    Connector Terminal Connector Terminal
    M213 7 M214 1 Yes
    8 2

  4. Check for continuity between wireless charger unit harness connector and ground.

    Wireless charger unit Ground Continuity
    Connector Terminal
    M213 7 No
    8

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the harnesses or connectors.

CHECK WIRELESS CHARGER INDICATOR GROUND CIRCUIT

Check for continuity between the wireless charger indicator harness connector and ground.

Wireless charger unit Ground Continuity
Connector Terminal
M213 4 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harnesses or connectors.

REPLACE WIRELESS CHARGER INDICATOR

  1. Replace wireless charger indicator.

  2. Ignition switch ON.

  3. Erase DTC.

  4. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC B1B05-09 detected again?

YES>>

Replace wireless charger unit. Refer to Removal and Installation.

NO>>

Inspection End.

U0079-00 Control Module Comm Bus G Off

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
U0079-00

Control module comm Bus G Off

(Control module communication Bus G Off) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission error or reception error
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "U0079‐00" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U0079‐00" detected?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U214f-87 Can Comm Err (bcm)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(CAN comm err (BCM)) 		DTC detection condition
U214F-87

CAN comm err (BCM)

(CAN comm err (BCM)) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission and reception error between wireless charger unit and BCM
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "U214F‐87" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U214F‐87" detected?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2118-87 Can Comm Err (intelligent Key)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
U2118-87

CAN comm err (Intelligent Key)

(CAN comm err (Intelligent Key)) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission and reception error between wireless charger unit and Intelligent Key
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "U2118‐87" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U2118‐87" detected?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U214e-87 Can Comm Err (combination Meter)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
U214E-87

CAN comm err (combination meter)

(CAN comm err (combination meter)) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission and reception error between wireless charger unit and combination meter
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "U214E‐87" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U214E‐87" detected?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U215b-87 Can Comm Err (ipdm E/r)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
U215B-87

CAN comm err (IPDM E/R)

(CAN comm err (IPDM E/R)) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission and reception error between wireless charger unit and IPDM E/R
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "U215B‐87" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U215B‐87" detected?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2148-87 Can Comm Err (brake Control Unit)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
U2148-87

CAN comm err (brake control unit)

(CAN comm err (brake control unit)) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission and reception error between wireless charger unit and ABS actuator and electric unit (control unit)
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication

FAIL-SAFE

Wireless charger unit does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "Wireless charger".

  3. Check DTC.

Is DTC "U2148‐87" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U2148‐87" detected?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

Power Supply and Ground Circuit

Wireless Charger Unit

Diagnosis Procedure

CHECK FUSE

Check for blown fuses.

Power source Fuse No. Capacity
Ignition switch ON or START 4 5A

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace the blown fuse after repairing the affected circuit.

CHECK IGNITION POWER SUPPLY CIRCUIT

  1. Ignition switch ON.

  2. Check voltage between wireless charger unit harness connector and ground.

    (+) (-) Standard Reference value
    Wireless charger unit
    Connector Terminal
    M213 1 Ground 9.0 - 16.0 V Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace wireless charger unit power supply harness.

CHECK GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect wireless charger unit connector.

  3. Check continuity between wireless charger unit harness connector and ground.

    Wireless charger unit Ground Continuity
    Connector Terminal
    M213 4 Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace wireless charger unit ground harness.

    Wireless Charger. Basic Inspection. Diagnosis and Repair Work Flow
    Diagnosis and Repair Work Flow Work Flow OVERALL SEQUENCEDETAILED FLOWINTERVIEW FOR MALFUNCTION It is also important to clarify the customer concerns before starting the inspect...
    Wireless Charger. Symptom Diagnosis. Wireless Charger System Symptoms
    Wireless Charger System Symptoms Symptom Table RELATED TO WIRELESS CHARGERMake sure the wireless charger is not in a deactivation condition before starting diagnosis. Refer to S...

    Other materials:

    Ecu Diagnosis Information. Bcm
    List of ECU Reference ECU Reference BCM Values on the Diagnosis Tool Reference Value (With Type A Meter) Reference Value (With Type B Meter) Fail-safe DTC Inspection Priority Chart DTC Index ...

    Removal and Installation. Drain Connector
    Exploded View Refer to Exploded View. Removal and Installation REMOVALFrontRemove instrument panel speaker. Without BOSE : Refer to Removal and Installation. With BOSE : Refer to Removal and Installation. Remove front wiper drive assembly. Refer to Removal and Installation. Dise ...

    Restraints. Seat Belt Control System
    Precaution :: Precautions Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to t ...