Nissan Rogue (T33) 2021-Present Service Manual: U2b52-88 Ethernet Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Adas Control Unit :: Dtc/circuit Diagnosis / U2b52-88 Ethernet Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U2B52 88 Ethernet comm err Diagnosis condition When engine is running
Signal (terminal) Ethernet communication
Threshold If ADAS control unit 2 is not receiving ethernet communication signal from around view monitor control unit
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Ethernet harness

  • ADAS control unit 2

  • Around view monitor control unit

FAIL-SAFE

The following systems are canceled.

  • Lane keep function*1

  • Lane keep function*2

  • Lane change support function

  • Overtaking support function

  • Route driving support function

  • FEB

  • RAB

  • PFCW

  • LDP

  • Blind Spot Intervention

  • TSR

*1: ProPILOT Assist 2.1 display is green

*2: ProPILOT Assist 2.1 display is blue

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine, and then wait for 2 seconds or more.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2B52-88” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “U2B52-88” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CONSULT DISPLAY AROUND VIEW MONITOR CONTROL UNIT

  1. Perform “All DTC Reading” with CONSULT.

  2. Check if the item of "AVM" is displayed in “All DTC Reading”.

Is "AVM" displayed?

YES>>

GO TO 2.

NO>>

Check power supply and ground circuit of around view monitor control unit. Refer to Diagnosis Procedure.

PERFORM SELF-DIAGNOSIS OF AROUND VIEW MONITOR CONTROL UNIT

Check if any DTC is detected in “Self Diagnostic Result” of “AVM”.

Is any DTC detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

GO TO 3.

CHECK ETHERNET CABLE

  1. Turn the ignition switch OFF.

  2. Check the Ethernet cable of ADAS control unit 2 and around view monitor control unit for disconnection, bending, and poor fitting.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace ethernet cable.

REPLACE ETHERNET CABLE

  1. Replace ethernet cable.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U2B52-88” detected as the current malfunction?

YES>>

GO TO 5.

NO>>

INSPECTION END

REPLACE AROUND VIEW MONITOR CONTROL UNIT

  1. Replace around view monitor control unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U2B52-88” detected as the current malfunction?

YES>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

NO>>

INSPECTION END

    U2952-88 Ethernet Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   U2952 88 Ethernet communication error Diagnosis condition...
    Power Supply and Ground Circuit
    Diagnosis Procedure CHECK FUSE Check that the following fuse is not blown: Signal name Fuse No. Ignition power supply 40 (10 A) Is the fuse blown? YES>> Replace the blown ...

    Other materials:

    Its Can Communication 2 Circuit
    Diagnosis Procedure CHECK CAN DIAGNOSIS Check the CAN diagnosis results from CONSULT to see that the ITS CAN communication 1 circuit and ITS CAN communication 4 circuit have no malfunction. Are the ITS CAN communication 1 circuit and ITS CAN communication 4 circuit normal? YES>> GO T ...

    Preparation
    Commercial Service Tools Tool Description Power tool Loosening screws Sealant or/and Lubricant Name Description Primer (3M K500, K520 or equivalent) Primer for attaching sonar sensor holder to bumper ...

    Symptom Diagnosis. Driver Side Power Window Does Not Operate
    Diagnosis Procedure CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY AND GROUND CIRCUIT Check power window main switch power supply and ground circuit. Refer to Diagnosis Procedure. Is the inspection result normal? YES>> GO TO 2. NO>> Repair or replace the malfunctioning parts. CHE ...