Nissan Rogue (T33) 2021-Present Service Manual: U2276-87 Can Comm Err (ccm)

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / U2276-87 Can Comm Err (ccm)

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U2276 87

CAN comm err (CCM)

[Controller area network communication error (chassis control module)] 		1 Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) CAN communication signal
Threshold When CAN communication signal is not continuously transmitted to chassis control module.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) CAN communication signal
Threshold When CAN communication signal is not continuously received from chassis control module.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • CAN communication line

 CAN communication system

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “U2276-87” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

    U225b-87 Can Comm Err (ipddm E/r)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U225B 87 CAN comm err (IPDDM E/R) [Controller area network c...
    U2a0b-88 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2A0B 88 Comm Bus Off CH2-CAN (Communication Bus Off CH2-CAN...

    Other materials:

    U2a8c-88 Ethernet Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition U2A8C-88 Ethernet circuit Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold Lost ethernet communication with AV control unit Diagnosis delay time ...

    P02cd Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02CD 00 CYL1 INJECTOR OFFSET LEARNING (Cylinder 1 Fuel Injector "A" Offset Learning At Max Limit) Diagnosis condition Engine running During injector ...

    B24a4-11 Intake Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24A4-11 INTAKE SENSOR (Intake sensor) Diagnosis condition Ignition switch ON Signal (Terminal) Intake sensor signal Threshold The intake sensor rec ...