Nissan Rogue (T33) 2021-Present Service Manual: U2a0b-88 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / U2a0b-88 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U2A0B 88

Comm Bus Off CH2-CAN

(Communication Bus Off CH2-CAN) 		1 Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) CAN communication signal
Threshold When CAN communication signal is not continuously transmitted from ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more
2 Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) CAN communication signal
Threshold When CAN communication signal is not continuously received from ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • CAN communication line

 CAN communication system

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “U2A0B-88” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

    U2276-87 Can Comm Err (ccm)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2276 87 CAN comm err (CCM) [Controller area network communi...
    U2a0e-88 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2A0E 88 Comm Bus Off CH2-FD (Communication Bus Off CH2-FD) ...

    Other materials:

    Power Socket. Removal and Installation. Power Socket
    Power Socket Console Power Socket Removal and Installation REMOVALRemove switch panel. Refer to Removal and Installation. Press the power socket fixing pawls from the back of the switch panel to remove the power socket. : Pawl INSTALLATIONNote the following, and install in the reve ...

    B2730-13 Side Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2730-13 SIDE SENSOR [RL] (Side sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH side Threshold H ...

    C1f41-84 Cvt
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F41 84 TRANSMISSION CIRCUIT (Transmission circuit) Diagnosis condition When engine is running When AEB system is O ...