Nissan Rogue (T33) 2021-Present Service Manual: U2248-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U2248 87 CAN communication error [ABS actuator and electric unit (control unit)] Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold Not receiving from ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Intelligent trace control function

  • Active ride control function

  • Automatic brake hold function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2248-87” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2248-87” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “ABS”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Check ABS actuator and electric unit (control unit) harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U2248-83 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2248 83 CAN communication error [ABS actuator and electric unit (control unit)] Diagnos...
    U2359-83 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2359 83 CAN communication error (steering unit) Diagnosis condition When ignition switc...

    Other materials:

    Preparation
    Special Service Tools The actual shapes of TechMate tools may differ from those of special service tools illustrated here. Tool number (TechMate No.) Tool name Description (NI-39570) Chassis ear Locates the noise (NI-50397) Squeak and Rattle Kit Repairs the cause o ...

    C10b1-01 Parking Brake Actuator (lh)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B1 01 Parking brake actuator (LH) [Parking brake actuator (left)] Diagnosis condition When parking brake is apply or release Signal (terminal) — ...

    Door Lock Function
    System Description SYSTEM DIAGRAMDoor lock function controls operation function of the following items. Door lock and unlock function (door request switch) Selective unlock function (door request switch) Reminder function (door request switch) Auto door lock function (door request ...