Nissan Rogue (T33) 2021-Present Service Manual: U2359-83 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U2359-83 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U2359 83 CAN communication error (steering unit) Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold Power steering control module in malfunctioning.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • Power steering control module

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2359-83” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2359-83” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK POWER STEERING CONTROL MODULE SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “EPS/DIRECT ADAPTIVE STEERING 3”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “EPS/DIRECT ADAPTIVE STEERING 3”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK POWER STEERING CONTROL MODULE SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect power steering control module harness connector.

  3. Check power steering control module harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect power steering control module harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U2248-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2248 87 CAN communication error [ABS actuator and electric unit (control unit)] Diagnos...
    U2359-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2359 87 CAN communication error (steering unit) Diagnosis condition When ignition switc...

    Other materials:

    C1213-A3 Control Unit Power Supply
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1213-A3 BATTERY VOLTAGE (Battery voltage) Diagnosis condition Ignition switch: ON Signal Battery power supply signal (terminal #6) Threshold Battery po ...

    Drive Pinion
    Kr15ddt Exploded View Drive pinion lock nut Companion flange Dust shield Drive pinion oil seal Pinion bearing assembly O-ring Drive pinion adjusting shim Drive pinion O-ring Transfer case oil seal Dowel pin Plug Gasket T ...

    B2723-88 Corner Sensor [rr]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2723-88 CORNER SENSOR [RR] (Corner sensor [RR]) Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Communication error D ...