Nissan Rogue (T33) 2021-Present Service Manual: U2154-87 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Adas Control Unit :: Dtc/circuit Diagnosis / U2154-87 Can Comm Circuit

Without Propilot Assist 2.1

DTC Description

CAN COMMUNICATION

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped with many electronic control units, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN-H, CAN-L) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads the required data only.

CAN communication signal chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
U2154 87

CAN comm err (MIU)

[Controller area network communication error (Multimedia interface unit)] 		Diagnosis condition

  • When engine is running

  • When AEB system is ON
Signal (terminal) CAN communication signal
Threshold If ADAS control unit 2 is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

NOTE:

If “U2154-87” is detected, first diagnose the CAN communication system.

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

None

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Turn the AEB system ON.

  3. Perform “All DTC Reading” with CONSULT.

  4. Check if the “U2154-87” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “U2154-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

With Propilot Assist 2.1

DTC Description

CAN COMMUNICATION

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped with many electronic control units, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN-H, CAN-L) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads the required data only.

CAN communication signal chart.Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
U2154 87 CAN communication error (steering angle sensor) Diagnosis condition When engine is running
Signal (terminal) CAN communication signal
Threshold If ADAS control unit 2 is not transmitting or receiving CAN communication signal
Diagnosis delay time 30 seconds or more

NOTE:

If “U2154-87” is detected, first diagnose the CAN communication system.

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following systems are canceled.

  • Lane keep function*

  • Lane change support function

  • Overtaking support function

  • Route driving support function

*: ProPILOT Assist 2.1 display is blue

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine, and then wait for 30 seconds or more.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2154-87” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “U2154-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair:Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM THE SELF-DIAGNOSIS

  1. Turn the ignition switch ON.

  2. Turn the AEB system ON, and then wait for 30 seconds or more.

  3. Perform “All DTC Reading” with CONSULT.

  4. Check if the “U2154-87” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “U2154-87” detected as the current malfunction?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

    U2153-87 Can Comm Circuit
    DTC Description CAN COMMUNICATIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communicatio...
    U2155-87 Can Comm Circuit
    Without Propilot Assist 2.1 DTC Description CAN COMMUNICATIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya ve...

    Other materials:

    Periodic Maintenance
    Periodic Maintenance The following tables show the normal maintenance schedule. Depending upon weather and atmospheric conditions, varying road surfaces, individual driving habits and Nissan Ariya vehicle usage, additional or more frequent maintenance may be required.Periodic maintenance beyo ...

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...

    Charge Air Cooler
    Exploded View Charge air cooler Charge air cooler Bracket 1 Turbocharger boost sensor (with intake air temperature sensor 2) O-ring Electronic throttle control actuator gasket Charge air cooler Bracket 2 Air inlet hose         To r ...