Nissan Rogue (T33) 2021-Present Service Manual: U2152-83 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U2152-83 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U2152 83 CAN communication error (ADAS control unit) Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold ADAS control unit 2 in malfunctioning.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • ADAS control unit 2

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2152-83” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2152-83” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK ADAS CONTROL UNIT 2 SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “ICC/ADAS 2”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “ICC/ADAS 2”.

Is DTC detected?

YES>>

Check the DTC.

  • Without ProPILOT Assist 2.1: Refer to DTC Index.

  • With ProPILOT Assist 2.1: Refer to DTC Index.

NO>>

GO TO 3.

CHECK ADAS CONTROL UNIT 2 SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect ADAS control unit 2 harness connector.

  3. Check ADAS control unit 2 harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect ADAS control unit 2 harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U2152-57 Mac Comm Error (adas Control Unit)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2152 57 CAN communication error (ADAS control unit) Diagnosis condition — Signal (ter...
    U2152-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2152 87 CAN communication error (ADAS control unit) Diagnosis condition When ignition s...

    Other materials:

    C10b1-01 Parking Brake Actuator (lh)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B1 01 Parking brake actuator (LH) [Parking brake actuator (left)] Diagnosis condition When parking brake is apply or release Signal (terminal) — ...

    Drive Pinion
    Kr15ddt Exploded View Drive pinion lock nut Companion flange Dust shield Drive pinion oil seal Pinion bearing assembly O-ring Drive pinion adjusting shim Drive pinion O-ring Transfer case oil seal Dowel pin Plug Gasket T ...

    Power Socket. Removal and Installation. Power Socket
    Power Socket Console Power Socket Removal and Installation REMOVALRemove switch panel. Refer to Removal and Installation. Press the power socket fixing pawls from the back of the switch panel to remove the power socket. : Pawl INSTALLATIONNote the following, and install in the reve ...